Time at JLM Shop:
LA500A & PEQ500A built and kits back in limited stock. If you want one order ASAP.

PCBs

This field is required.
  • Power Plant 2 Rail Power Supply PCB

    Power Plant 2 Rail Power Supply PCB

    JLM Audio Power Plant PCB 115vac/230vac to +24vdc @ 600mA and +48vdc @ 100mA power supply for running 4 x Neve, Telefunken and RCA BA modules. 2 x 12vac transformer for  +24vdc to +28vdc  for Neve, Telefunken etc 2 x 15vac transformer for  +28vdc to +36vdc for RCA BA** etc.  Super co…

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level29

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level29
  • DSUBHYPEX PCB

    DSUBHYPEX PCB

    DSUBHYPEX Audio Breakout PCB. (PCB with no parts only) TASCAM 8 channel audio 25 pin DSUB to 4 x HYPEX H-BUS IDC 14pin connectors and 26pin connector with all mute, temp and clip I/O.

    $16.50AUD inc GST for Australian Customers
    (Approx $10.15USD outside Australia)

    Stock Level5

    $16.50AUD inc GST for Australian Customers
    (Approx $10.15USD outside Australia)

    Stock Level5
  • STEREOBUS PCB

    STEREOBUS PCB

    STEREOBUS PCB is an 8 x 2 stereo virtual summing with stereo fader and balanced output. PCB size is 2" (50.8mm) x 2.6" (66mm). XLRs mount on 1" (25.4mm) centre spacing and each requires a 22mm hole.

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level2

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level2
  • EMU SP-1200 POWER SUPPLY PCB

    EMU SP-1200 POWER SUPPLY PCB

    5.0 average, based on 1 reviews

    EMU SP-1200 PC395 PUMP CHARGE POWER SUPPLY PCB. This Improved PCB replaces the original factory PC395 pcb which often develops a short circuit under the leaking caps.  Note you need to add the red link shown below when transferring or fitting parts to this pcb Replace the 5 Electro Caps…

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level3

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level3
  • GAIN Mic Pre / Makeup Amp PCB

    GAIN Mic Pre / Makeup Amp PCB

    GAIN is a gain block that with an input transformer can be used as a mic pre or unbalanced in as a makeup amp. It only needs a 48vdc power rail to run. From this, it supplies the opamp with +/-12vdc to +/-24vdc set by a trimpot, as well as supplying 48v for phantom power. Opamp voltage is set by…

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level28

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level28
  • Palpigrade 8 Channel Bal in to unbal out PCB

    Palpigrade 8 Channel Bal in to unbal out PCB

    Palpigrade 8 Channel balanced in to unbalanced output audio driver PCB Inputs on DB25 tascam or 26pin IDC header format to ribbon DB25 and output on 16pin IDC header or XLR/TRS if used with our TASCAM / IDC to XLR / TRS IN & OUT PCB at this link . Perfect compact way to add Balanced inputs …

    $24.20AUD inc GST for Australian Customers
    (Approx $14.88USD outside Australia)

    Stock Level23

    $24.20AUD inc GST for Australian Customers
    (Approx $14.88USD outside Australia)

    Stock Level23
  • Tardigrade 8 Channel unbal to Balance output PCB

    Tardigrade 8 Channel unbal to Balance output PCB

    Tardigrade 8 Channel unbalanced to balanced audio driver PCB. Inputs on 16pin IDC and output on DB25 tascam or 26pin IDC header format to ribbon DB25 or XLR/TRS if used with our TASCAM / IDC to XLR / TRS IN & OUT PCB at this link . Perfect compact way to add direct outputs to console and pro…

    $24.20AUD inc GST for Australian Customers
    (Approx $14.88USD outside Australia)

    Stock Level5

    $24.20AUD inc GST for Australian Customers
    (Approx $14.88USD outside Australia)

    Stock Level5
  • SUM8 PCB

    SUM8 PCB

    SUM8 8 Channel active virtual ground summing PCB. Use with AUX8 passive summing PCB and Palpigrade for balanced inputs and Tardigrade for balanced outputs. 4 stereo x 4 stereo matrix or 8 mono x 8 mono summing. PCB 4" (100mm) x 4" (100mm) Snaps into 4 x 1" (25mm) x 4" (100mm) pcbs. …

    $24.20AUD inc GST for Australian Customers
    (Approx $14.88USD outside Australia)

    Stock Level20

    $24.20AUD inc GST for Australian Customers
    (Approx $14.88USD outside Australia)

    Stock Level20
  • AUX8 PCB

    AUX8 PCB

    AUX8 8 Channel passive summing PCB. Use with SUM8 active virtual ground summing PCB and Palpigrade for balanced inputs and Tardigrade for balanced outputs. 4 stereo x 4 stereo matrix or 8 mono x 8 mono summing. PCB 4" (100mm) x 4" (100mm) Snaps into 4 x 1" (25mm) x 4" (100mm) pcbs …

    $30.80AUD inc GST for Australian Customers
    (Approx $18.94USD outside Australia)

    Stock Level24

    $30.80AUD inc GST for Australian Customers
    (Approx $18.94USD outside Australia)

    Stock Level24
  • 1290 Macro Mic Pre Main PCB

    1290 Macro Mic Pre Main PCB

    1290 Macro motherboard PCB is the quickest and most compact way to build a 1290/1073 mic pre. Only need to solder 36 parts to motherboard PCB + 2 x BAX83NV & 1 x BAX83AM modules whcih come fully built and tested. BAX83AM trim pot preset for Neve LO1166 & JLM111DC output transformer. Will work with…

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level4

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level4
  • V6 6 Rail Power Supply PCB

    V6 6 Rail Power Supply PCB

    V6 PCB - 6 rail super power supply kit for racking SSL and late model Neve modules. V6 can supply 3 x 1.5A positive power rails and 3 x 1.5A negative power rails. V6 has tracking and auto shutdown for each +/-V1 & +/-V2 pair of power rails. So +/- rails power up and shutdown together minimising thum…

    $31.90AUD inc GST for Australian Customers
    (Approx $19.62USD outside Australia)

    Stock Level17

    $31.90AUD inc GST for Australian Customers
    (Approx $19.62USD outside Australia)

    Stock Level17
  • RIBBON CABLETESTER PCB

    RIBBON CABLETESTER PCB

    CABLETESTER PCB makes ribbon cable testing quick and easy. Test for shorts and reversed plugs in seconds Powered by 2 x AAA batteries   PCB size is 4" (100mm) x 4" (100mm).  Build Thread here Parts List 1 x Cabletester PCB 1 x RED LED high brightness 1 x Green LED h…

    $16.50AUD inc GST for Australian Customers
    (Approx $10.15USD outside Australia)

    Stock Level0
    Out of stock

    $16.50AUD inc GST for Australian Customers
    (Approx $10.15USD outside Australia)

    Stock Level0
    Out of stock
  • STEREOLAB PCB

    STEREOLAB PCB

    STEREOLAB PCB converts stereo unbalanced to stereo balanced output with gain. Great for giving mobile phone or MP3 players professional balanced outputs. PCB can also take optional tiny MP3 pcb module under pcb with micro SDCard and USB drive support making it a fully functional pro audio MP3 …

    $19.80AUD inc GST for Australian Customers
    (Approx $12.18USD outside Australia)

    Stock Level31

    $19.80AUD inc GST for Australian Customers
    (Approx $12.18USD outside Australia)

    Stock Level31
  • 12PAKAMP Red PCB

    12PAKAMP Red PCB

    12PAKAMP RED PCB is a 12 channel version of our popular 60W AMP kit made to power and plug direct into a Hypex DLCP DSP card via its 10 and 20 pin IDC headers. 12 x 70Watt Amps configured as 6 x 140W bridged power amps. One amp for each output of the DLCP. 2 x 12000uF 50v capacitor power ra…

    $76.45AUD inc GST for Australian Customers
    (Approx $47.02USD outside Australia)

    Stock Level9

    $76.45AUD inc GST for Australian Customers
    (Approx $47.02USD outside Australia)

    Stock Level9
  • 12PAKAMP Blue PCB

    12PAKAMP Blue PCB

    12PAKAMP PCB is a 12 channel version of our popular 60W AMP kit. 12 x 70Watts of power configurable to lots of combination (eg 6 x 140watt bridged, 3 x 280watt bridged, 1 x 780watt bridged, 1 x 280watt bridged + 2 x 140watt bridged + 4 x 70watt. etc) 2 x 12000uF 50v capacitor power rail…

    $76.45AUD inc GST for Australian Customers
    (Approx $47.02USD outside Australia)

    Stock Level5

    $76.45AUD inc GST for Australian Customers
    (Approx $47.02USD outside Australia)

    Stock Level5
  • STATTEN PCB

    STATTEN PCB

    STereo U or H ATTENuater PCB for making passive mixes, volume or pan controls. PCB takes standard 16mm & 24mm pots as well as 16mm with switch. Dual 10k log pot for volume level control and Dual 10k lin pot for PAN.

    $7.70AUD inc GST for Australian Customers
    (Approx $4.74USD outside Australia)

    Stock Level20

    $7.70AUD inc GST for Australian Customers
    (Approx $4.74USD outside Australia)

    Stock Level20
  • DSUB4 PCB

    DSUB4 PCB

    TASCAM DB25 breakout PCB to IDC 26pin and 4 x 10 pin STBUS.  Allows TASCAM 8 channel DB25 breakout and power distribution to JLM products with IDC 26pin 8BUS and IDC 10pin STBUS Talkback Compressor kit 8 Channel relay switcher kit AMP HEAD phone Kit AMP HEAD II headphone Kit STATTE…

    $9.90AUD inc GST for Australian Customers
    (Approx $6.09USD outside Australia)

    Stock Level33

    $9.90AUD inc GST for Australian Customers
    (Approx $6.09USD outside Australia)

    Stock Level33
  • 8 Channel relay PCB

    8 Channel relay PCB

    8 Channel balanced audio relay switch PCB. In or out in DB25 tascam and IDC header format and XLR/TRS if used with our TASCAM / IDC to XLR / TRS IN & OUT PCB at this link  Relay driver on pcb so remote switching is easily done. 8 audio balanced channels can be switched seperately or in pair…

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level26

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level26
  • FET POWER SWITCHER PCB

    FET POWER SWITCHER PCB

    FET POWER SWITCHER PCB is used with our +/-16v@2A & +48v@120mA 65w SMPS power supply to give a simple single pole power switch that turns on the +/-16v and 48v with soft start using high current fets.

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level11

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level11
  • Talkback Compressor PCB

    Talkback Compressor PCB

    Compact and powerful talkback mic pre fet compressor PCB. Can be used as to build simple balanced in THAT1510 mic pre with balanced out with comp disabled. Neutrik Gold XLR in and out on PCB Talkback switch terminals Comp on/off threshold terminals 10 pin Amp Head plug THAT1510 mic pre…

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level83

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level83
  • Neve Interconnector PCB

    Neve Interconnector PCB

    Neve V - 51 Interconnector PCB. Makes it easy to rack up Neve V and Neve 51 series channel strips. Allows Neve V & 51 Module to run on +/-16v and 48v only. Use our pre built external +/-16v @ 2A & 48v @ 120mA 65W SMPS to run up to 4 Neve modules at once. Runs on 100vac to 250vac without switchin…

    $64.90AUD inc GST for Australian Customers
    (Approx $39.91USD outside Australia)

    Stock Level24

    $64.90AUD inc GST for Australian Customers
    (Approx $39.91USD outside Australia)

    Stock Level24
  • Powerstation 5 Rail Power Supply v5 Easy Mount PCB

    Powerstation 5 Rail Power Supply v5 Easy Mount PCB

    PowerStation Ver. 5 Easy Mount PCB makes a Linear based universal power supply which can generate 5 voltage rails from a single or dual 15 to 30vac power transformer.   Powerstation Ver 5 Easy Mount has rearranged PCB layout to even improve on its already outstanding performance and can mo…
    PCB Heatsink 5C/W & clamp OR L Bracket (Required)
    This field is required.

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level39

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level39
    This field is required.
    PCB Heatsink 5C/W & clamp OR L Bracket (Required)
    This field is required.
  • AC/DC 3 Rail Power Supply v5 Easy Mount PCB

    AC/DC 3 Rail Power Supply v5 Easy Mount PCB

    AC/DC Ver. 5 Easy Mount PCB makes a Linear based universal power supply that generates 3 voltage rails from a single or dual 15 to 30vac power transformer. AC/DC Ver 5 Easy Mount has rearranged PCB layout to even improve on its already outstanding performance and can mount to side and bottom o…
    PCB Heatsink 5C/W & clamp OR L Bracket (Required)
    This field is required.

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level94

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level94
    This field is required.
    PCB Heatsink 5C/W & clamp OR L Bracket (Required)
    This field is required.
  • MICRO DUAL SWITCH POT PCB

    MICRO DUAL SWITCH POT PCB

    Small PCB for our Shorting and Non Shorting  2 x 12 position rotary switches. Can be used for dual gain switch or dual frequency switch in lots of audio designs. PCB holds resistors and 4 pin headers so can convert normal and centre tapped single or dual pots to 12 position switched resistor ban…

    $5.50AUD inc GST for Australian Customers
    (Approx $3.38USD outside Australia)

    Stock Level44

    $5.50AUD inc GST for Australian Customers
    (Approx $3.38USD outside Australia)

    Stock Level44
  • XLR / TRS STEREO IO PCB

    XLR / TRS STEREO IO PCB

    STEREO IO PCB takes S2 or S4 cliff TRS sockets or Neutrik A & B series male and female connectors and brings them out on 3 way terminal blocks and JLM 10 pin IDC header which can plug direct into other JLM kits like AMP HEAD, Passive Monitor Controller etc.

    $9.90AUD inc GST for Australian Customers
    (Approx $6.09USD outside Australia)

    Stock Level183

    $9.90AUD inc GST for Australian Customers
    (Approx $6.09USD outside Australia)

    Stock Level183
  • TASCAM / IDC to XLR / TRS IN & OUT PCB

    TASCAM / IDC to XLR / TRS IN & OUT PCB

    8 WAY TASCAM DB25 pinout / IDC Ribbon cable breakout to TRS or XLR Male and Female connectors. PCB takes S2 or S4 Cliff TRS sockets and Neutrik A & B series male and female XLR's Can be used with the passive monitor Controller PCB to breakout all in and outs remotely over IDC ribbon cable. …

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level25

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level25
  • Passive Monitor Controller PCB Ver3

    Passive Monitor Controller PCB Ver3

    New more compact ver2 PCB to make Rob Squires Passive Monitor Controller easily. Click on image below to read PDF article. On this PCB mode control layout is MONO, STEREO, REV. R1 is 4K7 4 resitor SIL pack or 4 seperate 4k7 resistors Passive Monitor Controller PCB ver 2 size is 86.9mm (3.42") …

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level3

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level3
  • Hybrid Opamp PCB

    Hybrid Opamp PCB

    PCB for building the JLM Hybrid opamp with high current output drive transistors. It can have the output transistors set to run in Class A/B or Class A Mode. It also has on board DC Servo that can be enabled by soldering two solder pads together under the PCB. It is pin compatible with the JLM99v ,…

    $7.70AUD inc GST for Australian Customers
    (Approx $4.74USD outside Australia)

    Stock Level43

    $7.70AUD inc GST for Australian Customers
    (Approx $4.74USD outside Australia)

    Stock Level43
  • VU Buffer and Peak LED PCB

    VU Buffer and Peak LED PCB

    JLM VU Buffer & PEAK LED kit allows for a easy neat way to turn cheap dc type VU meters into working VU meters with PEAK LED. It is also extremely useful for buffering a real VU meter as it isolates the Total Harmonic Distortion caused by the internal rectifiers in the VU meter. This will usually…

    $8.80AUD inc GST for Australian Customers
    (Approx $5.41USD outside Australia)

    Stock Level30

    $8.80AUD inc GST for Australian Customers
    (Approx $5.41USD outside Australia)

    Stock Level30
  • Micro Passive Mixer PCB

    Micro Passive Mixer PCB

     Micro Passive Mixer PCB. 8 channel D25 to Stereo XLR output.  Several micro passive mixers can be daisy chained to make 64channel to Stereo XLR out passive mixer. D25 tascam standard pinout. Plug into back of protools D/A etc. Use pair of Neve, TG, Dual99v etc to give the …

    $10.45AUD inc GST for Australian Customers
    (Approx $6.43USD outside Australia)

    Stock Level150

    $10.45AUD inc GST for Australian Customers
    (Approx $6.43USD outside Australia)

    Stock Level150
  • AMP HEAD PCB

    AMP HEAD PCB

    AMP HEAD PCB Small size indestructable but extremely powerful and super low 0.001% THD stereo headphone amp kit with balanced inputs, volume control and buss connector to slave several AMP HEADs together. Also easy to add mono, mute and mix options. Can drive dead short on headphone jack ind…

    $10.45AUD inc GST for Australian Customers
    (Approx $6.43USD outside Australia)

    Stock Level37

    $10.45AUD inc GST for Australian Customers
    (Approx $6.43USD outside Australia)

    Stock Level37
  • KRAFTWERK PCB

    KRAFTWERK PCB

    NEW  KRAFTWERK 5 rail super power supply PCB is made to power up to 2 x 11 way 500 racks or 2 x 51X racks loaded with 11 x 500 & 11 x 51X Modules. Kraftwerk has tracking and auto shutdown for each +/-V1 & +/-V2 pair of power rails. So +/- rails power up and shutdown together minimising thumps and p…

    $31.90AUD inc GST for Australian Customers
    (Approx $19.62USD outside Australia)

    Stock Level6

    $31.90AUD inc GST for Australian Customers
    (Approx $19.62USD outside Australia)

    Stock Level6
  • MONO Ver2 PCB

    MONO Ver2 PCB

    MONO Ver2 PCB as used in our MONO mic pre ver2 kit. PCB with 2 x 9v batteries  fits in standard 119mm x 94mm x 35mm  Diecast Aluminium Box.

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level40

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level40
  • VU2 Stereo VU Buffer PCB

    VU2 Stereo VU Buffer PCB

    VU2 PCB is a stereo version of the normal VU buffer  but with some added features. Several PCB input options like 2 x XLR or 2 x TRS jacks or JLM Stereo port 10pin IDC or 3 way mini terminal blocks with pre wired plugs. PCB can be mounted by the PCB XLRs or TRS jacks or 2 x 3mm bolts. …

    $19.80AUD inc GST for Australian Customers
    (Approx $12.18USD outside Australia)

    Stock Level129

    $19.80AUD inc GST for Australian Customers
    (Approx $12.18USD outside Australia)

    Stock Level129
  • 8PAKAMP PCB

    8PAKAMP PCB

     8PAKAMP pcb is a 8 channel version of our popular 60W AMP pcb. We originally designed the 8PAKAMP for a large Dolby Labs project we did a while ago.   8 x 75Watts of power configurable to lots of combination (eg 4 x 140watt bridged, 2 x 280watt bridged, 1 x 560watt bridged, 1 x 280watt brid…

    $64.90AUD inc GST for Australian Customers
    (Approx $39.91USD outside Australia)

    Stock Level0
    Out of stock

    $64.90AUD inc GST for Australian Customers
    (Approx $39.91USD outside Australia)

    Stock Level0
    Out of stock
  • Regurgitator Single, Dual, Quad PCB

    Regurgitator Single, Dual, Quad PCB

    Regurgitator PCB can be used to convert any balanced or unbalanced signal in to balanced or unbalanced signal out with trim pot control from -10db loss to +18db gain. PCB comes as Single, Dual, or Quad PCBs Single PCB measures 58.2mm (2.3") x 25.4mm (1"). Dual PCB measures 58.2mm (2.3") x 5…
    Regurgitator PCB (Required)
    This field is required.

    $10.45AUD inc GST for Australian Customers
    (Approx $6.43USD outside Australia)

    Stock Level10

    $10.45AUD inc GST for Australian Customers
    (Approx $6.43USD outside Australia)

    Stock Level10
    This field is required.
    Regurgitator PCB (Required)
    This field is required.
  • Bridge and Cap PCB

    Bridge and Cap PCB

    Bridge and CAP PCB. Has 4 utilux terminals for a 2 x 12VAC to 35VAC toroidal transformer to connect. This feeds a on board 10A Bridge Rectifier and 4 x 10000uF 50v caps to make up to +/- 50v unreg with 20000uF of smoothing caps per rail. Daul output terminal can be utilux or screw terminals. …

    $11.00AUD inc GST for Australian Customers
    (Approx $6.77USD outside Australia)

    Stock Level166

    $11.00AUD inc GST for Australian Customers
    (Approx $6.77USD outside Australia)

    Stock Level166
  • TREX2 PCB 8PAK

    TREX2 PCB 8PAK

    TREX2 PCB 8PAK with V Groove snap off  

    $53.90AUD inc GST for Australian Customers
    (Approx $33.15USD outside Australia)

    Stock Level23

    $53.90AUD inc GST for Australian Customers
    (Approx $33.15USD outside Australia)

    Stock Level23
  • TREX PCB 12PAK

    TREX PCB 12PAK

    TREX PCB 12 PAK with V groove snap off.  

    $64.90AUD inc GST for Australian Customers
    (Approx $39.91USD outside Australia)

    Stock Level10

    $64.90AUD inc GST for Australian Customers
    (Approx $39.91USD outside Australia)

    Stock Level10
  • dINgO Pup PCB

    dINgO Pup PCB

    The dINgO pup kit allows for a easy neat way to have a high performance balanced IN to unbalanced output  and also a unbalanced input amp with gain to balanced Output  so can convert lots of unbalanced gear to balanced in and out. As well as providing the whole audio path for MAC comp & other …

    $19.80AUD inc GST for Australian Customers
    (Approx $12.18USD outside Australia)

    Stock Level15

    $19.80AUD inc GST for Australian Customers
    (Approx $12.18USD outside Australia)

    Stock Level15
  • JLM99MPPCBv2

    JLM99MPPCBv2

    The JLM99MBv2 PCB for the JLM99V which can take several transformers from manufacturers like OEP, Lundahl & Jensen. The board also has NE5534A DIP8 sockets so it can be fully tested with cheap IC's before installing the 99V. The PCB can be used for building the simplest NE5534A, OPA604A or 99V, 990,…

    $27.50AUD inc GST for Australian Customers
    (Approx $16.91USD outside Australia)

    Stock Level33

    $27.50AUD inc GST for Australian Customers
    (Approx $16.91USD outside Australia)

    Stock Level33
  • BAN PCB

    BAN PCB

    PCB for the Baby Animal Neutral super clean wire with gain 60dB single channel mic pre kit based on the Graham Cohen (National Semiconductor Designer) mic pre used in various forms by SSL, Neve Mozart, Amek 9098, Fred Forsell but made to work on a single 48v power rail.The mic pre has 20k input imp…

    $19.80AUD inc GST for Australian Customers
    (Approx $12.18USD outside Australia)

    Stock Level345

    $19.80AUD inc GST for Australian Customers
    (Approx $12.18USD outside Australia)

    Stock Level345
  • 1272/1073 18 Way Edge Connector PCB

    1272/1073 18 Way Edge Connector PCB

    18 way Edge connector PCB that fits Neve module rear connectors on 1272, 1073 , 1064, 1066, 1080, 1081 etc. R1 R2 R3 & C1 are all for 1272 modules. None need to be fitted for other full mic pre eq modules as it has them internally already. R1 is for 1272 1st stage gain boost R2 is used f…

    $11.00AUD inc GST for Australian Customers
    (Approx $6.77USD outside Australia)

    Stock Level13

    $11.00AUD inc GST for Australian Customers
    (Approx $6.77USD outside Australia)

    Stock Level13
  • dINgO PCB

    dINgO PCB

    The dINgO v3 PCB allows for a easy neat way to have a high performance balanced IN to unbalanced output  and also a unbalanced input amp with gain to balanced Output  so can convert lots of unbalanced gear to balanced in and out. As well as providing the whole audio path for MAC comp & other opto …

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level29

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level29
  • AMP PCB

    AMP PCB

    JLM AMP kit PCB AMP kit built thread here AMP PCB Measures 3" (76.2mm) x 1.5" (38.1mm).  Mounting holes 2.02" (51.31mm) apart and are in 0.49” (12.45mm) from edge and down 0.51” (12.95mm). Allow 1” (25.4mm) above PCB height and at least 0.2” (5.08mm) under PCB  …

    $19.80AUD inc GST for Australian Customers
    (Approx $12.18USD outside Australia)

    Stock Level222

    $19.80AUD inc GST for Australian Customers
    (Approx $12.18USD outside Australia)

    Stock Level222
  • PowerStation PCB

    PowerStation PCB

    Powerstation PCB  PowerStation kit Build Thread here PowerStation transformer and heatsink calculator here  

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level3

    $22.00AUD inc GST for Australian Customers
    (Approx $13.53USD outside Australia)

    Stock Level3
  • AC/DC PCB

    AC/DC PCB

    5.0 average, based on 1 reviews

    AC/DC ver 4 PCB New PCB as extra screw terminals making wiring to and from the PCB easier. Also all 4 mounting bolts can be used to connect to chassis ground as well a a case screw terminal. Also has back overlay showing the 3 most common AC/DC mods as well as terminal labels. AC/DC KIT…

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level11
    AC/DC PCB

    AC/DC PCB

    5.0 average, based on 1 reviews

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level11
  • BA PCB

    BA PCB

    Baby Animal PCB. BA PCB Size 123.1mm (4.825") x 35.6mm (1.4")  

    $19.80AUD inc GST for Australian Customers
    (Approx $12.18USD outside Australia)

    Stock Level17

    $19.80AUD inc GST for Australian Customers
    (Approx $12.18USD outside Australia)

    Stock Level17
  • BAD PCB

    BAD PCB

    BAD PCB  

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level263

    $20.90AUD inc GST for Australian Customers
    (Approx $12.85USD outside Australia)

    Stock Level263
15
Top

 

© 2001-2024. All rights reserved.