UA 4110 / 8110 Replacement SMPS +/-27v @ 0.74A +8v @ 2.5A +48v @ 200mA 70w SMPS  Direct bolt-in replacement for UA 4110 / 8110 Mic Pre Amplifier. Replaces Powdec power supply and 48v/Mute PCB.  Runs on 100vac to 250vac mains power without switching. Super low noise & smooth 30dB oc…

UA 2192 Replacement SMPS +/-27v @ 0.74A + 8v @ 3A 60w SMPS  Direct bolt-in replacement for UA 2192 Master Audio Interface.  Runs on 100vac to 250vac mains power without switching. Super low noise & smooth 30dB octave filtered dc outputs. All dc outputs 100% regulated to correct volta…

ACDC HV PCB is ideal for generating 2 regulated DC voltage rails from 24v to 60vdc @ 1.5A . Ideal for PM1000 channels needing 44vdc and 48vdc from a single 40vac to 50vac transformer winding. All 4 mounting bolts can be used to connect to chassis ground as well as a case screw terminal. …

NEW C6 - 6 rail super power supply kit for racking of ATI channel strips that require +/-48v @ 0.5A & +/-20 to +/-24vdc @ 1.5A & 5v @ 1.5A & 24vdc @ 1.5A. Dual pump charge circuits so 2 x 24vac transformer can generate +/-70vdc unregulated. C6 has tracking and auto shutdown for each +/-V1 & +/-V3…

JLM Audio Scorpion 30W tube power supply. 6-12v Filament, 48V & 2 × 50-300v power rails all regulated and trimpot adjustable. Switchable 115vac/230vac. VS sync allows syncing multiple Scorpion & Power plants with one 115vac/230vac voltage selection switch. Easy heatsink or case mount with on…

NEW TMP8 Large 48v 40w SMPS that is fully MEPS (Green energy rated) that can run on 80vac to 250vac without switching. Takes standard IEC power lead with 48v output on 5 Pin XLR connector. 

FET POWER SWITCHER Kit with PCB & PCb parts is used with our +/-16v@2A & +48v@120mA 65w SMPS power supply to give a simple single pole power switch that turns on the +/-16v and 48v with soft start using high current fets.

PowerStation Ver. 5 Easy Mount kit is a Linear based universal power supply which can generate 5 voltage rails from a single or dual 15 to 30vac power transformer.   Powerstation Ver 5 Easy Mount has rearranged PCB layout to even improve on its already outstanding performance and can mount …

AC/DC Ver. 5 kit Easy Mount is a Linear based universal power supply that generates 3 voltage rails from a single or dual 15 to 30vac power transformer. AC/DC Ver 5 Easy Mount has rearranged PCB layout to even improve on its already outstanding performance and can mount to side and bottom of c…

NEW Large +/-16v @ 2A + 48v @120mA 65w SMPS that is fully MEPS (Green energy rated) that can run on 100vac to 250vac without switching. Takes standard IEC power lead with output on 5pin XLR connector conforming to API 500 rack pinout. Ideal for running 12 x 500 modules or 500 racks. …

V6 - 6 rail super power supply kit for racking SSL and late model Neve modules. V6 can supply 3 x 1.5A positive power rails and 3 x 1.5A negative power rails. V6 has tracking and auto shutdown for each +/-V1 & +/-V2 pair of power rails. So +/- rails power up and shutdown together minimising thumps a…

IEC INLET with FUSE and POWER SWITCH in a snap in block. Unit is internally wired with only Active Neutral and Earth terminals on the rear of the block. For use with our Power Plant and World transformer kits etc  

100vac to 250vac 5v 2A SMPS Plug pack used to run VUPPM Stereo Meter Compact & VUPPM Ver 3 kits when on board 5v to +/-12v SMPS fitted. Comes with snap-on world mains plugs for all countries.  

 DC chassis connector that matches the output connector on our 12v & 48v SMPS. This connector does NOT join the 0v of the power supply to the chassis so can be used to make a +48v rail or +/-24v etc. Requires 8mm hole to mount.

Diecast Heatsink Machined & Tapped for M5 bolts for Kraftwork PCB. 150mm x 75mm x 38mm. Photo of Kraftwerk Power supply bolted to heatsink

KRAFTWERK 5 rail super power supply kit powers up to 2 x 11 way 500 racks or 2 x 51X racks loaded with 11 x 500 & 11 x 51X Modules. Kraftwerk has tracking and auto shutdown for each +/-V1 & +/-V2 pair of power rails. So +/- rails power up and shutdown together minimising thumps and pops in any audio…

 Cable used to power 2 DC powered kits from one power supply

JLM Audio Power Plant kit. Full 115vac/230vac to +24vdc @ 600mA and +48vdc @ 100mA power supply for running 4 x Neve, Telefunken and RCA BA modules. Order with 2 x 12vac transformer for  +24vdc to +28vdc  for Neve, Telefunken etc Order with 2 x 15vac transformer for  +28vdc to +36vdc for RC…

Tiny Internal 48v 15w 315mA SMPS. Runs on mains voltage of 85vac to 265vac without switching. Dimensions 62.5mm x 51mm x 28mm

Use this kit with our powerstation kit to make a +/-16v @ 3Amp +48v @ 500mA power supply for API VPR 500 series racks. Has standard 500 series XLR pin out and 3 led indicators to show power rails are up and running. If more 5pin XLR outputs needed PS500XLR PCB can be connected together …

Bridge and CAP kit. Comes with 4 utilux terminals for connecting a 2 x 12VAC to 35VAC toroidal transformer. This feeds a on board 10A Bridge Rectifier and 4 x 10000uF 50v caps to make up to +/- 50v unreg with 20000uF of smoothing caps per rail. Daul screw output terminal allow star wiring to …

5Deg.C/W heatsink for TREX2

NEW Large 48v 40w SMPS that is fully MEPS (Green energy rated) that can run on 80vac to 250vac without switching. Takes standard IEC power lead with 48v output on 2.1mm DC connector. Ideal for running 4 to 8 of our Baby Animal, BA4, mic pre kits. The 48v output is fairly smooth and noise free as …

NEW 48v 520mA 25W SMPS that is fully MEPS (Green energy rated) that can run on 80vac to 250vac without switching. (Same physical size as our old 48v 380mA SMPS) Takes standard IEC power lead with 48v output on 2.1mm DC connector. Ideal for running all of our Baby Animal, BA2, Stereo Dual99v, Ste…

100vac to 250vac 12v 1A SMPS Plug pack used to run VU buffer kits and VU lamps or LEDs. Comes with snap-on world mains plugs for all countries.

DC chassic connector that matches the output connector on our 48v 520mA SMPS. This connector joins the 0v of the power supply to the chassis as well so can only be used to make +48v rail. Requires 8mm hole to mount.

JLM TREX2 simple reg kit is a very simple Linear based universal power supply with can generate two 5v to 28v from a single 30v to 48vdc rail. It can do other output voltages by changing to different voltage zeners or if running from a regulated higher rail a trim pot can be used in place o…

JLM TREX simple reg kit is a very simple Linear based universal power supply with can generate a 5v to 28v from a single 30v to 48vdc rail. It can do other output voltages by changing to different voltage zeners or if running from a regulated higher rail a trim pot can be used in place o…

JLM World Power kit is a fully fused & 120v/240VAC switchable 30VA PCB power transformer to dual low voltage AC out. Kit can be ordered with 3 different transformers with either 2 x 9vac or 2 x 12vac or 2 x 15vac outputs. This kit with either a AC/DC or Powerstation kit will give you a full …

JLM PowerStation Ver. 3 kit is a Linear based universal power supply which can generate 5 voltage rails from a single or dual 15 to 30vac power transformer.   It has one pump charge rail for 48vdc, 2 +/- Rails that can be set from +/-2v to 37v by a 25turn trim pot. All regulators are on on…

JLM AC/DC Ver. 4 kit is a Linear based universal power supply that generates 3 voltage rails from a single or dual 15 to 30vac power transformer. It has one pump charge rail for 48vdc, 1 +/- Rails that can be set from +/-2v to 37v by a 25turn trim pot. All regulators are on one edge for easy …