Time at JLM Shop:

Small interface Kits

This field is required.
  • DSUBHYPEX KIT

    DSUBHYPEX KIT

    DSUBHYPEX Audio Breakout KIT. (KIT comes with PCB and PCB mounted parts to be soldered together) TASCAM 8 channel audio 25 pin DSUB to 4 x HYPEX H-BUS IDC 14pin connectors and 26pin connector with all mute, temp and clip I/O.

    €17,25

    Stock Level10
    Info

    €17,25

    Info
    Stock Level10
  • XLR IO 2503 Kit

    XLR IO 2503 Kit

    XLR IO 2503 Kit gives an easy way to mount any 2503 transformer to a case either by bolts or by the pair of XLRs These are used in our latest BA2 & BA4 kits XLR hole details below Click on the image below for a larger image All measurements in millimeters

    €40,25

    Stock Level35
    Info

    €40,25

    Info
    Stock Level35
  • GAIN Mic Pre / Makeup Amp Kit

    GAIN Mic Pre / Makeup Amp Kit

    5.0 average, based on 1 reviews

    GAIN is a gain block that with an input transformer can be used as a mic pre or unbalanced in as a makeup amp. It only needs a 48vdc power rail to run. From this, it supplies the opamp with +/-12vdc to +/-24vdc set by a trimpot, as well as supplying 48v for phantom power. Opamp voltage is set by…
    Opamp sockets (Required)
    Opamp (Required)
    Output Transformer (Required)
    Power Supply (Required)
    This field is required.

    €25,88

    Stock Level18
    Info

    €25,88

    Info
    Stock Level18
    This field is required.
    Opamp sockets (Required)
    This field is required.
    Opamp (Required)
    This field is required.
    Output Transformer (Required)
    This field is required.
    Power Supply (Required)
    This field is required.
  • Passive Monitor Controller Kit Ver3

    Passive Monitor Controller Kit Ver3

    New more compact ver3 PCB kit to make Rob Squires Passive Monitor Controller easily. Click on the image below to read the PDF article. On this PCB mode control layout is MONO, STEREO, REV. R1 is 4K7 or 5k1 4 resistor SIL pack or 4 separate 4k7 or5k1 resistors Passive Monitor Controller PCB ve…
    Pot Type (Required)
    This field is required.

    €23,00

    Stock Level0
    Out of stock
    Info

    €23,00

    Info
    Stock Level0
    Out of stock
    This field is required.
    Pot Type (Required)
    This field is required.
  • Palpigrade 8 Channel Bal in to unbal out kit

    Palpigrade 8 Channel Bal in to unbal out kit

    Palpigrade 8 Channel balanced in to unbalanced output audio driver kit. Inputs on DB25 tascam or 26pin IDC header format to ribbon DB25 and output on 16pin IDC header or XLR/TRS if used with our TASCAM / IDC to XLR / TRS IN & OUT PCB at this link . Perfect compact way to add Balanced inputs…
    16pin plug and cable (Required)
    Opamps (Required)
    This field is required.

    €28,18

    Stock Level9
    Info

    €28,18

    Info
    Stock Level9
    This field is required.
    16pin plug and cable (Required)
    This field is required.
    Opamps (Required)
    This field is required.
  • Tardigrade 8 Channel unbal to Balance output kit

    Tardigrade 8 Channel unbal to Balance output kit

    5.0 average, based on 1 reviews

    Tardigrade 8 Channel unbalanced to balanced audio driver kit. Inputs on 16pin IDC and output on DB25 tascam or 26pin IDC header format to ribbon DB25 or XLR/TRS if used with our TASCAM / IDC to XLR / TRS IN & OUT PCB at this link . Perfect compact way to add direct outputs to console and pro…
    16pin plug and cable (Required)
    Opamps (Required)
    This field is required.

    €28,18

    Stock Level1
    Info

    €28,18

    Info
    Stock Level1
    This field is required.
    16pin plug and cable (Required)
    This field is required.
    Opamps (Required)
    This field is required.
  • Go Between RC Kit

    Go Between RC Kit

    JLM Go Between RC kit.  This RC kit provides a quick and easy way to add ramped 48v phantom power, 20dB PAD & Phase reverse switching that can be remote controlled by a single SPDT switches with or without leds or lamps running on 5v to 48v & +/-6v to +/-24v power rails. Can be used to help rack …
    3 & 5 pin sockets & plugs with 300mm wire (Required)
    This field is required.

    €14,38

    Stock Level31
    Info

    €14,38

    Info
    Stock Level31
    This field is required.
    3 & 5 pin sockets & plugs with 300mm wire (Required)
    This field is required.
  • Variable HPF kit

    Variable HPF kit

    Variable HPF kit for adding into mixing consoles, channel strips and mic pres. 10k unbalanced buffered input (can be changed to 1Meg by changing R4 from 10k to 1Meg) 500ohm to 2k output impedance depending on opamp used. Variable 50Hz to 500Hz with 100nF caps fitted. Variable 22Hz to 2…

    €14,38

    Stock Level7
    Info

    €14,38

    Info
    Stock Level7
  • RIBBON CABLETESTER KIT

    RIBBON CABLETESTER KIT

    5.0 average, based on 1 reviews

    CABLETESTER KIT makes ribbon cable testing quick and easy. Test for shorts and reversed plugs in 10 to 50 pin dual row 2.54mm cables in seconds Powered by 2 x AAA batteries   PCB size is 4" (100mm) x 4" (100mm).  Build Thread here Parts List 1 x Cabletester PCB 1 x R…
    Built and Tested (Required)
    This field is required.

    €28,18

    Stock Level28
    Info
    RIBBON CABLETESTER KIT

    RIBBON CABLETESTER KIT

    5.0 average, based on 1 reviews

    €28,18

    Info
    Stock Level28
    This field is required.
    Built and Tested (Required)
    This field is required.
  • STEREOLAB KIT

    STEREOLAB KIT

    STEREOLAB KIt converts stereo unbalanced to stereo balanced output with gain. Great for giving mobile phone or MP3 players professional balanced outputs. PCB can also take optional tiny MP3 pcb module under pcb with micro SDCard and USBdrive support making it a fully functional pro audio MP3 pl…
    MP3 player parts
    Input Connector Type (Required)
    This field is required.

    €22,43

    Stock Level7
    Info

    €22,43

    Info
    Stock Level7
    This field is required.
    MP3 player parts
    This field is required.
    Input Connector Type (Required)
    This field is required.
  • STATTEN Kit

    STATTEN Kit

    STereo U or H ATTENuater kit for making passive mixes, volume or pan controls. PCB takes standard 16mm & 24mm pots as well as 16mm with switch. Dual 10k log pot for volume level control and Dual 10k lin pot for PAN.
    Pad Type (Required)
    Pot Type (Required)
    This field is required.

    €5,46

    Stock Level20
    Info

    €5,46

    Info
    Stock Level20
    This field is required.
    Pad Type (Required)
    This field is required.
    Pot Type (Required)
    This field is required.
  • DSUB4 Kit

    DSUB4 Kit

    DSUB4 Audio Breakout Kit. Breaks TASCAM 8 channel audio to IDC and 4 x BALIO Ports. TASCAM DB25 breakout PCB to IDC 26pin and 4 x 10 pin STBUS.  Allows TASCAM 8 channel DB25 breakout and power distribution to JLM products with IDC 26pin 8BUS and IDC 10pin STBUS connectors. Talkback Co…

    €10,93

    Stock Level6
    Info

    €10,93

    Info
    Stock Level6
  • 8 Channel relay switcher kit

    8 Channel relay switcher kit

    5.0 average, based on 1 reviews

    8 Channel balanced audio relay switch kit. In or out in DB25 tascam and IDC header format and XLR/TRS if used with our TASCAM / IDC to XLR / TRS IN & OUT PCB at this link  Relay driver on pcb so remote switching is easily done. 8 audio balanced channels can be switched seperately or in pair…
    Relay Voltage (Required)
    This field is required.

    €28,18

    Stock Level18
    Info

    €28,18

    Info
    Stock Level18
    This field is required.
    Relay Voltage (Required)
    This field is required.
  • Neve V-51 Interconnect Kit

    Neve V-51 Interconnect Kit

    Neve V - 51 Interconnector Kit. PCB & PCB Parts. Makes it easy to rack up Neve V and Neve 51 series channel strips. Allows Neve V & 51 Module to run on +/-16v and 48v only. Use our pre built external +/-16v @ 2A & 48v @ 120mA 65W SMPS to run up to 4 Neve modules at once. Runs on 100vac to 250vac…
    Power section parts (Required)
    This field is required.

    €56,93

    Stock Level6
    Info

    €56,93

    Info
    Stock Level6
    This field is required.
    Power section parts (Required)
    This field is required.
  • REPRO passive reamp kit

    REPRO passive reamp kit

    REPRO passive reamp kit. Perfect for converting balanced line out level down to unbalanced guitar level with full volume and tone impedance adjustment. REPRO Build Thread click here REPRO reamp kit parts list 1 x Hammond black plastic box 1 x REPRO front panel 1 x JLM14 transformer 1 x Pl…

    €78,20

    Stock Level8
    Info

    €78,20

    Info
    Stock Level8
  • Micro Passive Mixer Kit

    Micro Passive Mixer Kit

    Micro Passive Mixer kit. 8 channel D25 to Stereo XLR output.  Several micro passive mixers can be daisy chained to make 64channel to Stereo XLR out passive mixer. D25 tascam standard pinout. Plug into back of protools D/A etc. Use pair of Neve, TG, Dual99v etc to give the passive mix the …

    €45,43

    Stock Level1
    Info

    €45,43

    Info
    Stock Level1
  • Stereo In Out Kit

    Stereo In Out Kit

    …
    Input Connector Type (Required)
    This field is required.

    €9,20

    Stock Level15
    Info

    €9,20

    Info
    Stock Level15
    This field is required.
    Input Connector Type (Required)
    This field is required.
  • Regurgitator Single Dual Quad Kit

    Regurgitator Single Dual Quad Kit

    5.0 average, based on 1 reviews

    Regurgitator can convert any balanced or unbalanced signal in to balanced or unbalanced signal out with trim pot control from -10db loss to +18db gain. Regurgitators PCB comes as Single or Dual or Quad PCBs. For example if you order 8 kits and select Dual PCB you will get 4 Dual PCB or i…
    Regurgitator PCB (Required)
    Input (Required)
    Opamp (Required)
    Output (Required)
    This field is required.

    €14,38

    Stock Level6
    Info

    €14,38

    Info
    Stock Level6
    This field is required.
    Regurgitator PCB (Required)
    This field is required.
    Input (Required)
    This field is required.
    Opamp (Required)
    This field is required.
    Output (Required)
    This field is required.
  • dINgO Pup Kit

    dINgO Pup Kit

    The dINgO pup kit allows for a easy neat way to have a high performance balanced IN to unbalanced output  and also a unbalanced input amp with gain to balanced Output  so can convert lots of unbalanced gear to balanced in and out. As well as providing the whole audio path for MAC comp & other …
    Balanced In and Out (Required)
    Opamp (Required)
    This field is required.

    €28,18

    Stock Level8
    Info

    €28,18

    Info
    Stock Level8
    This field is required.
    Balanced In and Out (Required)
    This field is required.
    Opamp (Required)
    This field is required.
  • Variable Pad Kit

    Variable Pad Kit

    5.0 average, based on 1 reviews

    The Variable input pad kit plugs into the DI socket on the Go Between kit or GO Between PLUS kit to give a 25dB variable pad. The 20dB fixed pad switch on the GO Between or GO between PLUS kit still functions so up to 45dB of attenuation can be achieved. A JLM Fet DI or JLM OPA DI can sti…

    €8,63

    Stock Level7
    Info
    Variable Pad Kit

    Variable Pad Kit

    5.0 average, based on 1 reviews

    €8,63

    Info
    Stock Level7
  • XLR IO Kit

    XLR IO Kit

    Click on image below for larger image All measurements in millimeters

    €9,20

    Stock Level19
    Info

    €9,20

    Info
    Stock Level19
  • dINgO Kit

    dINgO Kit

    The dINgO kit allows for a easy neat way to have a high performance balanced IN to unbalanced output  and also a unbalanced input amp with gain to balanced Output  so can convert lots of unbalanced gear to balanced in and out. As well as providing the whole audio path for VCA & MAC opto compress…
    Opamp sockets (Required)
    1. Opamp (Required)
    2. Opamp (Required)
    Balanced In and Out (Required)
    Output Transformer (Required)
    This field is required.

    €28,75

    Stock Level16
    Info

    €28,75

    Info
    Stock Level16
    This field is required.
    Opamp sockets (Required)
    This field is required.
    1. Opamp (Required)
    This field is required.
    2. Opamp (Required)
    This field is required.
    Balanced In and Out (Required)
    This field is required.
    Output Transformer (Required)
    This field is required.
  • Go Between Plus Kit

    Go Between Plus Kit

    5.0 average, based on 1 reviews

    JLM Go Between PLUS kit provides a quick and easy way to add ramped 48v phantom power, 20dB PAD, Phase reverse & Input transformer to help rack API & Quad8 etc amp cards or add these extra features to mic pres without them. Also has a IDC connected for adding either of the JLM DI kits in seconds. G…

    €17,25

    Stock Level19
    Info
    Go Between Plus Kit

    Go Between Plus Kit

    5.0 average, based on 1 reviews

    €17,25

    Info
    Stock Level19
  • Fet DI Kit

    Fet DI Kit

     JLM FET DI Kit just plugs into the GO Between or GO between PLUS or Any Baby Animal type PCB by a 10pin IDC cable which will do all connections and power the DI or you can just cut into the Cable coming from the Mic Input XLR that goes to the input transformer primary on any mic pre and it only ne…

    €23,00

    Stock Level8
    Info

    €23,00

    Info
    Stock Level8
  • Go Between Kit

    Go Between Kit

    5.0 average, based on 2 reviews

    JLM Go Between kit This kit provides a quick and easy way to add ramped 48v phantom power, 20dB PAD & Phase reverse switching to help rack API & Quad8 etc amp cards or add these extra features to mic pres without them. Also has a IDC connected for adding either of the JLM DI kits in seconds.  …

    €14,38

    Stock Level198
    Info
    Go Between Kit

    Go Between Kit

    5.0 average, based on 2 reviews

    €14,38

    Info
    Stock Level198
12
Top

 

© 2001-2024. All rights reserved.