Time at JLM Shop:

Opamps

This field is required.
  • DOA Solder to Sockets adaptor

    DOA Solder to Sockets adaptor

    Socket adaptor for replacing soldered-in Yamaha NE80100 & NE80200 opamps with 2520 / 990 socket footprint so opamps can be plugged in and swapped easily. The PCB Pads and holes in the old Yamaha PCBs are too small to be drilled out for the sockets. This adaptor makes it easy as it can solder in w…

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level30

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level30
  • TA7136 to 990/2520 DOA adaptor

    TA7136 to 990/2520 DOA adaptor

    Socket adaptor for replacing 7 pin SIL TA7136 opamps with 2520 / 990 footprint type DOA  The adaptor can have SIL pins mounted offset by 7.5mm (0.3") left or right to help it fit in tight spaces. TA7136 are used in many old Yamaha PM2000, M1516, M1524, M1532 etc consoles.

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level30

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level30
  • HA1457 to 990/2520 DOA adaptor

    HA1457 to 990/2520 DOA adaptor

    Socket adaptor for replacing 8 pin SIL HA1457 opamps with 2520 / 990 footprint type DOA The adaptor can have SIL pins mounted offset by 7.5mm (0.3") left or right to help it fit in tight spaces.  HA1457 are used in many old Yamaha PM2000, M1516, M1524, M1532 etc consoles.

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level30

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level30
  • TA7322 to 990/2520 DOA adaptor

    TA7322 to 990/2520 DOA adaptor

    Socket adaptor for replacing 9 pin SIL TA7322 opamps with 2520 / 990 footprint type DOA  The adaptor can have SIL pins mounted offset by 7.5mm (0.3") left or right to help it fit in tight spaces. TA7322 are used in many old Yamaha PM2000, M1516, M1524, M1532 etc consoles.

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level30

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level30
  • DIP8 to 2520/990 Adaptor

    DIP8 to 2520/990 Adaptor

    Socket adaptor for replacing Single DIP8 opamps with 2520 / 990 type DOA footprint  

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level30

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level30
  • 990A+ opamp

    990A+ opamp

    5.0 average, based on 1 reviews

    Our modern version on the Deane Jensen 990 opamp. Due to our improved dual constant currents tracking more than 10 times better than the original, the C upgrade for wide voltage range is not needed so the design is closer to the original 990 version but can run on even wider voltage range. We have a…

    $73.15AUD inc GST for Australian Customers
    (Approx $44.63USD outside Australia)

    Stock Level39
    990A+ opamp

    990A+ opamp

    5.0 average, based on 1 reviews

    $73.15AUD inc GST for Australian Customers
    (Approx $44.63USD outside Australia)

    Stock Level39
  • Hybrid SMDv2 Opamp

    Hybrid SMDv2 Opamp

    The JLM Hybrid SMDv2 is a fet input IC opamp with high current output drive transistors. It can have the output transistors set to run in Class A/B or Class A Mode that can be enabled by soldering two solder pads together on top of the PCB. It is pin-compatible with the JLM99v, 990, 992, 993, MM99…

    $53.90AUD inc GST for Australian Customers
    (Approx $32.88USD outside Australia)

    Stock Level19

    $53.90AUD inc GST for Australian Customers
    (Approx $32.88USD outside Australia)

    Stock Level19
  • Twenty 5 Twenty SMD Opamp

    Twenty 5 Twenty SMD Opamp

    5.0 average, based on 3 reviews

    Twenty 5 Twenty SMD opamp is an amazing sounding extreme precision version of the old original 2520 opamp.  Voltage range of +/-12v to +/-25v. Precision 1% matched input transistor diff pair Precision 1% matched second stage transistor diff pair. Improved thermal layout for least DC off…

    $49.50AUD inc GST for Australian Customers
    (Approx $30.20USD outside Australia)

    Stock Level22

    $49.50AUD inc GST for Australian Customers
    (Approx $30.20USD outside Australia)

    Stock Level22
  • FLICK535 SMD Opamp

    FLICK535 SMD Opamp

    Our modern take on the FLICKinger opamp with standard discrete 990 2520 pinout but now in SMD Power +/-15vdc to +/-28vdc (Below +/-24vdc THD increases slowly to 0.06% @ +/15vdc) Draws 10mA to 20mA @ idle   H1 { TEXT-ALIGN: center } H2 { FONT-SIZE: 14pt } H3 {FONT-FAMILY: Verdana,Ari…

    $53.90AUD inc GST for Australian Customers
    (Approx $32.88USD outside Australia)

    Stock Level45

    $53.90AUD inc GST for Australian Customers
    (Approx $32.88USD outside Australia)

    Stock Level45
  • TA7136 SMD Opamp replacement

    TA7136 SMD Opamp replacement

    TA7136 SMD replacement opamp can replace old TA7136 SIL opamps used in many old Yamaha consoles.   Uses dual opamp as one opamp so can drive 300ohm loads and run on +/-18vdc max. Improves performance especially in summing amp positons. Parts list SMD Adaptor PCB 7 gold pin strip …

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level26

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level26
  • HS3099 Opamp

    HS3099 Opamp

    HS3099 opamp is a modern version of the Sontec HS2000 & HS2030 in a 2520 / 990 footprint but with several improvements for longer reliable life without tonal changes. Voltage range +/-24vdc or +/-28vdc @ 40mA no load. Frequency range DC to 10MHz. Hand matched devices. Improved constant …
    Servo pin will be used via 51k? (Required)
    Voltage (Required)
    This field is required.

    $192.50AUD inc GST for Australian Customers
    (Approx $117.44USD outside Australia)

    Stock Level10

    $192.50AUD inc GST for Australian Customers
    (Approx $117.44USD outside Australia)

    Stock Level10
    This field is required.
    Servo pin will be used via 51k? (Required)
    This field is required.
    Voltage (Required)
    This field is required.
  • NE5533 to 2xNE5534A Adaptor

    NE5533 to 2xNE5534A Adaptor

    Socket adaptor for replacing NE5533 dual opamps with two modern single DIP8 opamps like NE5534AP etc.  

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level45

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level45
  • HS7000 Opamp

    HS7000 Opamp

    HS7000 opamp is a modern version of the Sontec HS6000 but with several improvements for longer reliable life without tonal changes. The HS7000 can also replace HS6000 and also 990 / 2520 foot print opamps in Sontec clones and other equipment. When ordering let us know if you want them as Sont…
    Pinout type (Required)
    This field is required.

    $104.50AUD inc GST for Australian Customers
    (Approx $63.76USD outside Australia)

    Stock Level0
    Out of stock

    $104.50AUD inc GST for Australian Customers
    (Approx $63.76USD outside Australia)

    Stock Level0
    Out of stock
    This field is required.
    Pinout type (Required)
    This field is required.
  • ITI to Sontec Filter

    ITI to Sontec Filter

    Plug in Sontec Filter to replace old ITI EQs filter pcb with potted rectangle filter opamps. Replaces broken ITI Filter modules with Sontec type filter.  The ITI to Sontec Filter replaces the below type ITI filter modules.  

    $77.00AUD inc GST for Australian Customers
    (Approx $46.98USD outside Australia)

    Stock Level8

    $77.00AUD inc GST for Australian Customers
    (Approx $46.98USD outside Australia)

    Stock Level8
  • ITI Filter Adaptor

    ITI Filter Adaptor

    Plug in adaptor to replace old ITI EQs filter pcb with potted rectangle filter opamps. Allows discrete opamps like JLM99v, JLM 25HV, JLM35HVFET, FLICK535, HYBRID etc to plug in and run on +/-24v or +/-28v power rails. The ITI filter adaptor replaces the below type ITI filter modules. …

    $55.00AUD inc GST for Australian Customers
    (Approx $33.56USD outside Australia)

    Stock Level3

    $55.00AUD inc GST for Australian Customers
    (Approx $33.56USD outside Australia)

    Stock Level3
  • ITI Opamp Adaptor

    ITI Opamp Adaptor

    Plug in adaptor to replace old ITI EQs amp pcb with 3 potted rectangle opamps. Allows discrete opamps like JLM99v, JLM 25HV, JLM35HVFET, FLICK535 etc to plug in and run on the +/-28v power rails. The ITI Amp adaptor replaces the below type ITI audio path modules.

    $99.00AUD inc GST for Australian Customers
    (Approx $60.40USD outside Australia)

    Stock Level10

    $99.00AUD inc GST for Australian Customers
    (Approx $60.40USD outside Australia)

    Stock Level10
  • HS3030 Opamp

    HS3030 Opamp

    HS3030 opamp is a modern version of the Sontec HS2030 but with several improvements for longer reliable life without tonal changes. The HS3030 can also replace HS2000 with a quick desolder of a solder link. If using as HS2000 leave note in comments so we will setup the opamp before shipping. …

    $192.50AUD inc GST for Australian Customers
    (Approx $117.44USD outside Australia)

    Stock Level6

    $192.50AUD inc GST for Australian Customers
    (Approx $117.44USD outside Australia)

    Stock Level6
  • DUAL to 2xSINGLE DIP8 Adaptor

    DUAL to 2xSINGLE DIP8 Adaptor

    Socket adaptor for replacing DUAL DIP8 opamps with two modern single DIP8 opamps like OPA604AP or NE5534AP etc.  

    $19.80AUD inc GST for Australian Customers
    (Approx $12.08USD outside Australia)

    Stock Level3

    $19.80AUD inc GST for Australian Customers
    (Approx $12.08USD outside Australia)

    Stock Level3
  • TL074 to 2xDual DIP8 Adaptor

    TL074 to 2xDual DIP8 Adaptor

    Socket adaptor for replacing TL074 quad opamps with two modern dual DIP8 opamps like OPA2604AP or NE5532AP etc.  

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level6

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level6
  • FLICK535 opamp

    FLICK535 opamp

    Our modern take on the FLICKinger opamp with standard discrete 990 2520 pinout Power +/-16vdc to +/-28vdc (Below +/-24vdc THD increases slowly to 0.06% @ +/16vdc) Draws 10mA to 20mA @ idle   H1 { TEXT-ALIGN: center } H2 { FONT-SIZE: 14pt } H3 {FONT-FAMILY: Verdana,Arial; FONT-SIZE: …

    $65.45AUD inc GST for Australian Customers
    (Approx $39.93USD outside Australia)

    Stock Level0
    Out of stock

    $65.45AUD inc GST for Australian Customers
    (Approx $39.93USD outside Australia)

    Stock Level0
    Out of stock
  • 6 x 1mm gold opamp pins

    6 x 1mm gold opamp pins

    6  x 1mm pins for Hybrid discrete opamps. 

    $2.20AUD inc GST for Australian Customers
    (Approx $1.34USD outside Australia)

    Stock Level189

    $2.20AUD inc GST for Australian Customers
    (Approx $1.34USD outside Australia)

    Stock Level189
  • TA7322P & HA1457 replacement opamp kit

    TA7322P & HA1457 replacement opamp kit

    5.0 average, based on 1 reviews

    TA7322P & HA1457 replacement opamp kit v2 can replace old TA7322P & HA1457 SIL opamps used in many old Yamaha PM2000, M1516, M1524, M1532 etc consoles.   Uses dual NE5532AP as one opamp so can drive 300ohm loads and run on +/-25vdc max. Improves performance, especially in summing amp position…

    $27.50AUD inc GST for Australian Customers
    (Approx $16.78USD outside Australia)

    Stock Level19

    $27.50AUD inc GST for Australian Customers
    (Approx $16.78USD outside Australia)

    Stock Level19
  • BAX83AM Module

    BAX83AM Module

      Compact version of the Neve BA183AM or BA283AM output amp section as used in our Micro1290 and Macro1290 kits  

    $49.50AUD inc GST for Australian Customers
    (Approx $33.22USD outside Australia)

    Stock Level6

    $49.50AUD inc GST for Australian Customers
    (Approx $33.22USD outside Australia)

    Stock Level6
  • BAX83NV Module

    BAX83NV Module

    Compact version of the Neve BA183NV or BA283NV preamp section as used in our Micro1290 and Macro1290 kits 

    $54.45AUD inc GST for Australian Customers
    (Approx $33.22USD outside Australia)

    Stock Level12

    $54.45AUD inc GST for Australian Customers
    (Approx $33.22USD outside Australia)

    Stock Level12
  • Sontec HS10** SMD Opamp Adaptor

    Sontec HS10** SMD Opamp Adaptor

    Plug in adaptor for old Sontecs EQs or Comps with potted rectangle opamps like HS1000, HS1020 and HS1050. Allows discrete opamps like JLM99v, HYBRID SMDv2, FLICK SMD, 990, 992, 993 etc to plug in and run on either +/-28v or +/-24v by soldering or unsoldering 4 solder pads.   Unsolder link…

    $33.00AUD inc GST for Australian Customers
    (Approx $20.13USD outside Australia)

    Stock Level23

    $33.00AUD inc GST for Australian Customers
    (Approx $20.13USD outside Australia)

    Stock Level23
  • V8 Opamp Kit

    V8 Opamp Kit

    JLM V8 opamp kit uses 4 x dual standard opamps like NE5532AP, OPA2604AP, TL072, LM833, OPA2134 to make a brut powerful hard load driving opamp with low THD. All 8 opamp outputs share the load. Pinout is standard 99v, 2520, 990, 992, 993. 4 x NE5532AP can drive 60ohm load on +/-12v to +/-18…
    Opamps (Required)
    This field is required.

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level4

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level4
    This field is required.
    Opamps (Required)
    This field is required.
  • Hybrid Opamp Built

    Hybrid Opamp Built

    The JLM Hybrid is a fet input IC opamp with high current output drive transistors. It can have the output transistors set to run in Class A/B or Class A Mode. It also has on board DC Servo that can be enabled by soldering two solder pads together under the PCB. It is pin compatible with the JLM99v …

    $64.90AUD inc GST for Australian Customers
    (Approx $39.60USD outside Australia)

    Stock Level0
    Out of stock

    $64.90AUD inc GST for Australian Customers
    (Approx $39.60USD outside Australia)

    Stock Level0
    Out of stock
  • NE5532AP Dual Opamp

    $5.50AUD inc GST for Australian Customers
    (Approx $3.36USD outside Australia)

    Stock Level144

    $5.50AUD inc GST for Australian Customers
    (Approx $3.36USD outside Australia)

    Stock Level144
  • OPA2604AP Opamp

    OPA2604AP Opamp

    Burr Brown OPA2604AP as used in our Original opamp DI kit and BA kits. Voltage Supply max +/-25v

    $13.20AUD inc GST for Australian Customers
    (Approx $8.05USD outside Australia)

    Stock Level0
    Out of stock

    $13.20AUD inc GST for Australian Customers
    (Approx $8.05USD outside Australia)

    Stock Level0
    Out of stock
  • 6 x 1mm Sockets

    6 x 1mm Sockets

    6  x 1mm sockets for all of our BA, BAD, BAN PCB's. Sockets fit in 1.83mm hole on PCB and allow for plugging in 99v, Hybrid discrete opamps. 

    $6.60AUD inc GST for Australian Customers
    (Approx $4.03USD outside Australia)

    Stock Level52

    $6.60AUD inc GST for Australian Customers
    (Approx $4.03USD outside Australia)

    Stock Level52
  • Hybrid Opamp Kit

    Hybrid Opamp Kit

    We are selling the hybrid kit without opamps at the moment due to OPA2604AP being unavailable while TI try to fix the overheating problem since they moved the opamp onto a new smaller silicon fab. You can run any dual fet input opamp on there up to the max voltage of the opamp used. Opamps like TL07…
    Opamp (Required)
    This field is required.

    $31.90AUD inc GST for Australian Customers
    (Approx $19.46USD outside Australia)

    Stock Level0
    Out of stock

    $31.90AUD inc GST for Australian Customers
    (Approx $19.46USD outside Australia)

    Stock Level0
    Out of stock
    This field is required.
    Opamp (Required)
    This field is required.
  • 4136 to 2xDual DIP8 Adaptor

    4136 to 2xDual DIP8 Adaptor

    Socket adaptor for replacing 4136 quad opamps with two modern dual DIP8 opamps like OPA2604AP or NE5532AP etc. Good for upgrading LA4 compressors or Carver C1 hifi preamps or any device that uses 4136 opamps. Black LA4 needs 2 x 4136 adaptor and replace round output opamp with DIP8 wirewrap s…

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level30

    $22.00AUD inc GST for Australian Customers
    (Approx $13.42USD outside Australia)

    Stock Level30
  • JLM99v Opamp +/-16v to +/-24v

    JLM99v Opamp +/-16v to +/-24v

    JLM99V opamp +/-16v is our JLM99v rebiased for lower voltage power rails like used in our 500 series equipment. It is a pure path device with the signal path only travelling through three transistor junctions. It has gain limited to about 60dB with no feedback applied. When setup right the THD with…

    $82.50AUD inc GST for Australian Customers
    (Approx $50.33USD outside Australia)

    Stock Level58

    $82.50AUD inc GST for Australian Customers
    (Approx $50.33USD outside Australia)

    Stock Level58
  • JLM99v Opamp +/-24v to +/-34v

    JLM99v Opamp +/-24v to +/-34v

    JLM99V opamp is like a Neve Class A Preamp on major Steroids. It is a pure path device with the signal path only travelling through three transistor junctions. It has gain limited to about 60dB with no feedback applied. When setup right the THD with feedback is 0.005% at normal operating levels head…

    $82.50AUD inc GST for Australian Customers
    (Approx $50.33USD outside Australia)

    Stock Level22

    $82.50AUD inc GST for Australian Customers
    (Approx $50.33USD outside Australia)

    Stock Level22
17
Top

 

© 2001-2024. All rights reserved.