Time at JLM Shop:

C6 +/- Dual Pump Charge 6 Rail Power Supply Kit

C6 +/- Dual Pump Charge 6 Rail Power Supply Kit
  • Click to enlarge
Heatsink 200mm x 75mm x 48mm
Built and Tested (Required)

$86.90AUD inc GST for Australian Customers
(Approx $54.20USD outside Australia)
Change currency to see all prices including options in your preferred currency.

(Quantity discounts available)


Product Information
Quantity Discounts
Stock Level9

NEW C6 - 6 rail super power supply kit for racking ATI channel strips that require +/-48v @ 0.5A & +/-24v @ 1.5A & 5v @ 3A. Dual pump charge circuits so 2 x 18vac transformer can generate +/-70vdc regulated. C6 has tracking and auto shutdown for each +/-V1 & +/-V3 pair of power rails. So +/- rails power up and shut down together minimizing thumps and pops in any audio equipment it is powering. Also if a fault over currents and shuts down a power rail the other power rail will shut down in sync protecting expensive DOA and DIP8 opamps from internal latch-up which can kill opamps. Uses silicon tubes on regs and 4 x 5mm bolts to locate PCB and hold the regs firm to the heatsink. So no white bush and hole burr cutting silicon pad problems. Can be quickly released from the heatsink in seconds for any maintenance.  Fits on back or front or inside 2 rack unit high cases.  C6 kit is PCB + all PCB parts. The heatsink is an optional extra. For powering pairs of most ATI  modules rack case side, back, or bottom panel is enough heatsinking for C6.

Features

  • Dual pump charge so 2 x 18vac transformer can generate +/-70vdc regulated.
    6 power rails. (4 positive and 2 negative @ 1.5Amp each) 
  • Can make one +V and one -V rail @3A with tracking protection.
  • 16000uF (8000uF per +/-rail) Super smoothing cap bank.
  • +/-V1 & +/-V3 tracking. (eg the +/-V1 & +/-V3 power rails will track each other while powering up or down within +/-0.3v stopping most thumps and pops)
  • +/-V1 & +/-V3 auto shutdown. (eg if the +16v goes into protect and shuts down it will put down the -16v automatically as well and vica versa) 
  • +/-V3 can both be set to extra normal +/-V rail or pump charged doubled or tripled for +/-35v to +/-70v rail with 2 simple jumpers.
  • C6 PCB is ROHS HASL PLATED with thick copper.  
  • C6 PCB measuring a tiny 130mm (5.11") x 66.5mm (2.62") 

 

C6 Parts List here

C6 Build Thread here

C6 Schematic here


C6 can be configured for below and many other combinations.

ATI Channels to provide  +/- 48v @ 0.5A & +/- 24v @ 1.5A & 2 x 5v @ 1.5A
500 series only to provide +16vdc @ 3Amp / -16vdc @ 3Amp and +48vdc @ 400mA using a 2 x 18vac 160VA to 225VA.

51X series to provide +24vdc @ 3Amp / -24vdc @ 3Amp and +48vdc @ 400mAusing a 2 x 22vac 225VA to 300VA.

 Optional Heatsink is 200mm wide x 75mm high x 38mm deep. Made to fit on back, front or inside 2 unit high rack cases.

C6 PCB topside

   

C6 PCB Bottomside

You can save money on this item when you purchase several at a time. The table below shows the minimum quantities required to benefit from this offer, and how much they'll cost.


QuantityPrice per unit
1$86.90AUD
5+$83.60AUD
10+$79.20AUD

Customer Reviews

This product hasn't been reviewed yet.

Write a review

Write Review

Anti-Spam Test
Please enter a valid email address.
This field is required.
Top

 

© 2001-2022. All rights reserved.