20 x M3 x 8mm countersunk bolts used in Sidekick and Eleven racks for holding in 500 modules.  Order 1 for 1 pack of 20 bolts. 2 for 40 bolts etc

NV500 Green PCB Recap kit 2 x 3300uF 25v 3 x 470uF 50v 1 x 100uF 35v 1 x 4700uF 16v

Clip with double sided tape like used to hold JLM14 transformer in our Repro kits

25Amp 400v Bridge rectifier for use with our Powerstaion, Kraftwerk & V6 kits

DPDT RELAY 12v as used on BIO500v2 PCB

Socket adaptor for replacing DUAL DIP8 opamps with two modern single DIP8 opamps like OPA604AP or NE5534AP etc.  

Socket adaptor for replacing TL074 quad opamps with two modern dual DIP8 opamps like OPA2604AP or NE5532AP etc.  

470R SIL 4 Buss Resistor as used in AMP Head and AMP Head II kits 2 off these are used per AMP Head pcb  

Replacement backlight led for our 34mm round VU meters. Square and round parts of meter snap apart and sclae slides up to reveal 5mm clear led which can be unsolder from to posts and replaced.

Matched Opto Pair for LA500 and LA500A.

24v (+/-12v) to 5v 1W SMPS as used in our VUPPM kit 

5v to +/-12v 1W SMPS as used in our VUPPM kit 

 DB25 shielded cover

  DB25 Female connector with solder cup rear connections  

DB25 Male connector with solder cup rear connections 

Double Ferrite Bead used in BAN kits You need 2  Double Ferrite Beads for each BAN PCB 

Pair of 10 pin IDC Cable Headers 

2SK170 FET as used in our FET DI kit.

500mm length of 10 wire grey ribbon cable for use with IDC plugs

2 x 9v NiMH rechargeable batteries for MONO mic pre kit

Dual99v 1 rack unit flat Front panel with laser text not drilled (Note 2). This front panel is made to be used with Baby Animal Dual (BAD) and older original Dual99v kits. Panel can hold 2 mic pre kits with variable impedance and 2 DI kits. Note 2. These Flat Front Panels have all holes fully ce…

1272 rack 1 rack unit flat Front panel with laser text not drilled (Note 2). This front panel is made to be used with 2 x 1272 Neve mic pre modules. Panel can hold two 1272 with JLM 1272 to 1290 modules fitted  to make 75dB mic pre. Panel takes 2 x of our GO between kits and DI kits as well as…

25Amp 400v Bridge rectifier for use with our AMP kit or most power amplifier or high current power supplies.

Set of 8 soft limiter 3.5mm stereo plugs set to match your A/D converter. The TMP8 ships with a set new so you only need to order another set if you change to a A/D that has a different clip level. Just mention your A/D type or the dBM or dBu clip level in the comments box on checkout so we can supp…

BA4 1 rack unit flat Front panel with laser text not drilled (Note 2). This front panel is made to be used with Baby Animal (BA), Baby Animal Dual (BAD) and Baby Animal Neutral (BAN) kits. Panel can hold 4 mic pre kits and 2 DI kits. Note 2. These Flat Front Panels have all holes fully centre m…

BA2 1 rack unit flat Front panel with laser text not drilled (Note 2). This front panel is made to be used with Baby Animal (BA), Baby Animal Dual (BAD) and Baby Animal Neutral (BAN) kits. Panel can hold 2 mic pre kits with variable impedance and 2 DI kits. Note 2. These Flat Front Panels have…

DI Socket for OPA Opamp DI kit   Will replace all sockets that look the same like in Lexicon LXP1 etc. Cut off any pins on new socket that are not on original old socket and fit to PCB.

6  x 1mm sockets for all of our BA, BAD, BAN PCB's. Sockets fit in 1.83mm hole on PCB and allow for plugging in 99v, Hybrid discrete opamps. 

470uF 50v Capacitor used in our Baby Animal, Baby Animal Dual and Baby Animal Neutral kit and PCB's. 10mm diameter.

1000uF 50v Capacitor used in our AC/DC and Powerstation kit. 13mm diameter.

Socket adaptor for replacing 4136 quad opamps with two modern dual DIP8 opamps like OPA2604AP or NE5532AP etc. Good for upgrading LA4 compressors or Carver C1 hifi preamps or any device that uses 4136 opamps. Black LA4 needs 2 x 4136 adaptor and replace round output opamp with DIP8 wirewrap s…