Time at JLM Shop:

Mod Kits

Kits for modifying other brand products


 

This field is required.
  • HS3030 Opamp

    HS3030 Opamp

    HS3030 opamp is a modern version of the Sontec HS2030 but with several improvements for longer reliable life without tonal changes. The HS3030 can also replace HS2000 with one resistor removed if pin 4 on the HS2000 isn't used. If using as HS2000 leave note in comments at checkout and we will re…

    $192.50AUD inc GST for Australian Customers
    (Approx $123.01USD outside Australia)

    Stock Level39

    $192.50AUD inc GST for Australian Customers
    (Approx $123.01USD outside Australia)

    Stock Level39
  • DUAL to 2xSINGLE DIP8 Adaptor

    DUAL to 2xSINGLE DIP8 Adaptor

    Socket adaptor for replacing DUAL DIP8 opamps with two modern single DIP8 opamps like OPA604AP or NE5534AP etc.  

    $19.80AUD inc GST for Australian Customers
    (Approx $12.65USD outside Australia)

    Stock Level10

    $19.80AUD inc GST for Australian Customers
    (Approx $12.65USD outside Australia)

    Stock Level10
  • TL074 to 2xDual DIP8 Adaptor

    TL074 to 2xDual DIP8 Adaptor

    Socket adaptor for replacing TL074 quad opamps with two modern dual DIP8 opamps like OPA2604AP or NE5532AP etc.  

    $22.00AUD inc GST for Australian Customers
    (Approx $14.06USD outside Australia)

    Stock Level8

    $22.00AUD inc GST for Australian Customers
    (Approx $14.06USD outside Australia)

    Stock Level8
  • Neve Interconnector Kit

    Neve Interconnector Kit

    Neve V - 51 Interconnector Kit. PCB & PCB Parts. Makes it easy to rack up Neve V and Neve 51 series channel strips. Allows Neve V & 51 Module to run on +/-16v and 48v only. Use our pre built external +/-16v @ 2A & 48v @ 120mA 65W SMPS to run up to 4 Neve modules at once. Runs on 100vac to 250vac…
    +/-16v@2A & +48v 65w SMPS
    This field is required.

    $108.90AUD inc GST for Australian Customers
    (Approx $69.59USD outside Australia)

    Stock Level34

    $108.90AUD inc GST for Australian Customers
    (Approx $69.59USD outside Australia)

    Stock Level34
    This field is required.
    +/-16v@2A & +48v 65w SMPS
    This field is required.
  • PM Opamp Adaptor Kit v2

    PM Opamp Adaptor Kit v2

    5.0 average, based on 1 reviews

    PM Adaptor kit v2 can replace old TA7322P & HA1457 SIL opamps used in many old Yamaha PM2000, M1516, M1524, M1532 etc consoles.   Uses dual NE5532AP as one opamp so can drive 300ohm loads and run on +/-25vdc max. Improves performance especially in summing amp positons. In some postions in …

    $27.50AUD inc GST for Australian Customers
    (Approx $17.57USD outside Australia)

    Stock Level34
    PM Opamp Adaptor Kit v2

    PM Opamp Adaptor Kit v2

    5.0 average, based on 1 reviews

    $27.50AUD inc GST for Australian Customers
    (Approx $17.57USD outside Australia)

    Stock Level34
  • Sontec Opamp Adaptor

    Sontec Opamp Adaptor

    Plug in adaptor for old Sontecs EQs or Comps with potted rectangle opamps like HS1000, HS1020 and HS1050. Allows descrete opamps like JLM99v, Hybrid, JLM 25HV, JLM35HVFET, 990, 992, 993 etc to plug in and run on either +/-28v or +/-24v by removing the 2 jumpers. Leave jumper links fitted (…

    $33.00AUD inc GST for Australian Customers
    (Approx $21.09USD outside Australia)

    Stock Level6

    $33.00AUD inc GST for Australian Customers
    (Approx $21.09USD outside Australia)

    Stock Level6
  • PM2000 Solo Mod Kit

    PM2000 Solo Mod Kit

    5.0 average, based on 1 reviews

    JLM PM2000 Solo mod kit when applied to all channels in a PM2000 type desk will make the normal mono CUE buttons give true stereo solo in place by muting all channels without CUE pressed. This gives you a more accurate solo signal than most normal desks as it keeps the audio path the same as when so…

    $16.50AUD inc GST for Australian Customers
    (Approx $10.54USD outside Australia)

    Stock Level344
    PM2000 Solo Mod Kit

    PM2000 Solo Mod Kit

    5.0 average, based on 1 reviews

    $16.50AUD inc GST for Australian Customers
    (Approx $10.54USD outside Australia)

    Stock Level344
  • PM2000 EQ Mod Kit

    PM2000 EQ Mod Kit

    The JLM AUDIO PM2000 EQ mod kit when applied to High Mids and Low Mids of a Yamaha PM2000 , M1516, M1524, M1532 desk will change the narrow Gyrator (IC) type EQ into fully inductive (LCR) wider EQ.  Can also be used to add frequencies for Bass and Mids in PM1000 channels.  This kit contai…

    $55.00AUD inc GST for Australian Customers
    (Approx $35.15USD outside Australia)

    Stock Level15

    $55.00AUD inc GST for Australian Customers
    (Approx $35.15USD outside Australia)

    Stock Level15
  • 4136 to 2xDual DIP8 Adaptor

    4136 to 2xDual DIP8 Adaptor

    Socket adaptor for replacing 4136 quad opamps with two modern dual DIP8 opamps like OPA2604AP or NE5532AP etc. Good for upgrading LA4 compressors or Carver C1 hifi preamps or any device that uses 4136 opamps. Black LA4 needs 2 x 4136 adaptor and replace round output opamp with DIP8 wirewrap s…

    $22.00AUD inc GST for Australian Customers
    (Approx $14.06USD outside Australia)

    Stock Level4

    $22.00AUD inc GST for Australian Customers
    (Approx $14.06USD outside Australia)

    Stock Level4
22
Top

Follow Us

Mailing List

Enter your e-mail address to receive our newsletter
Please enter a valid email address.
Email address already subscribed. Continue if you wish to unsubscribe.
Subscribe
Unsubscribe