Search found 39 matches
- Tue Aug 20, 2013 12:37 am
- Forum: JLM Audio Kits
- Topic: BA BA2 BA4 BAD Dual99v Build Thread
- Replies: 376
- Views: 963259
Re: BA BA2 BA4 BAD Dual99v Build Thread
Hi Joe, I just wired my second BA Mic pre and it seems to be getting no power, the transformer and the opamp remains cold compared to the first BA Pre where the opamp and transformer seem to heat reasonably fast. I tested the pre with a mic and got a small level coming in, -24Dbfs on Didgidesign 192...
- Fri May 10, 2013 4:22 pm
- Forum: JLM Audio Kits
- Topic: BA BA2 BA4 BAD Dual99v Build Thread
- Replies: 376
- Views: 963259
Re: BA BA2 BA4 BAD Dual99v Build Thread
Hi JOe,
Just wondering if should be using something like shielded Canare wire to connect to the XLR's or is it not going to make much of difference?
Thanks
AJ
Just wondering if should be using something like shielded Canare wire to connect to the XLR's or is it not going to make much of difference?
Thanks
AJ
- Fri May 10, 2013 12:35 am
- Forum: JLM Audio Kits
- Topic: BA BA2 BA4 BAD Dual99v Build Thread
- Replies: 376
- Views: 963259
Re: BA BA2 BA4 BAD Dual99v Build Thread
Hi Joe, Well I think it's working. I turned it on and nothing exploded, smoked or fried :) I haven't tested the voltages yet, not quite sure how to do that but I ran a bass guitar through and there was sound, no hiss, and plenty of low end. I then went Bass - SansAmp Bass Driver; Active - JLM pre an...
- Thu May 09, 2013 1:29 pm
- Forum: JLM Audio Kits
- Topic: BA BA2 BA4 BAD Dual99v Build Thread
- Replies: 376
- Views: 963259
Re: BA BA2 BA4 BAD Dual99v Build Thread
Hi Joe, I have LED and the power switch sorted. HOw do I wire the Hi Z pot? Do I use both 2k2 resistors or just 1? And do i solder the resistor across both pins? Thanks AJ Wired as shown in the BA4 overlay in the post above. No Rload on the PCB. Instead wire 2 wires out to a resistor in series with...
- Wed May 08, 2013 11:54 pm
- Forum: JLM Audio Kits
- Topic: BA BA2 BA4 BAD Dual99v Build Thread
- Replies: 376
- Views: 963259
Re: BA BA2 BA4 BAD Dual99v Build Thread
Hi Joe,
Just wondering how I wire my EA2623 if I don't have and output trim pot? I saw another thread but the guy had an out put trim pot and the brown wire went to an xlr out via the trim pot?
Thanks
AJ
Just wondering how I wire my EA2623 if I don't have and output trim pot? I saw another thread but the guy had an out put trim pot and the brown wire went to an xlr out via the trim pot?
Thanks
AJ
- Wed May 08, 2013 10:30 pm
- Forum: JLM Audio Kits
- Topic: BA BA2 BA4 BAD Dual99v Build Thread
- Replies: 376
- Views: 963259
Re: BA BA2 BA4 BAD Dual99v Build Thread
Hi Joe,
I have LED and the power switch sorted. HOw do I wire the Hi Z pot? Do I use both 2k2 resistors or just 1? And do i solder the resistor across both pins?
Thanks
AJ
I have LED and the power switch sorted. HOw do I wire the Hi Z pot? Do I use both 2k2 resistors or just 1? And do i solder the resistor across both pins?
Thanks
AJ
- Wed May 08, 2013 4:44 pm
- Forum: JLM Audio Kits
- Topic: BA BA2 BA4 BAD Dual99v Build Thread
- Replies: 376
- Views: 963259
Re: BA BA2 BA4 BAD Dual99v Build Thread
Hi Joe, Thanks for you info regarding my previous questions. All good now. With the power switch I got a special bag labelled 'use in power switch' that had a LED and a resistor. I've place the LED on the circuit board, I assumed the long anode goes into the hole that joins the circuit and the short...
- Tue May 07, 2013 3:05 pm
- Forum: JLM Audio Kits
- Topic: BA BA2 BA4 BAD Dual99v Build Thread
- Replies: 376
- Views: 963259
Re: FIRST DIY BUILDS: JLM BAs & 1290 Complete!
Also, this may seem dumb but with the ea2622 Input Transformer what colour should pin one be in on the BA PCB?
- Tue May 07, 2013 3:04 pm
- Forum: JLM Audio Kits
- Topic: BA BA2 BA4 BAD Dual99v Build Thread
- Replies: 376
- Views: 963259
Re: FIRST DIY BUILDS: JLM BAs & 1290 Complete!
Is there any change in sonic quality using the 220pf capacitors instead of the 47pf capacitors in the opamp section with GAR2520op?