JLM AUDIO

saxmonster wrote: ↑

Wed Feb 07, 2024 3:44 pm

Thanks Joe,
Once I get them equal should I drop the output of my daw so that I get 1.23vac on both opto outputs so I can zero out the meter when I recalibrate?

Yes

Hi Joe, I have started to work with figuring out what exact resistor size I would need. I have not made any changes or soldered anything yet. In doing that I decided to setup my Apogee duet interface to use for the REW Signal generator because both outputs are equal on that. With that said I sent 1...

Alex1990 wrote: ↑

Wed Feb 07, 2024 8:34 am

Ok so there still appears to be a short - in addition to this I had to cut a couple legs to get it out so not exactly workable. My desoldering is getting better but this was a tricky one

Short on the PCB or the pot?

Hello Joe, I just completed my first of two Audio Path PCBs. Per the build guide, I went to test it, inserted the two jumpers, connected it to an extender...and when I powered on my rack, the two 4R7 resistors instantly fried. Any troubleshooting tips? Best to post here or send me photos of the top...

Thanks again for all you help Joe. You can add a resistor across channel B makeup pot outside pads to balance the outputs exactly. Somewhere between 240k and 330k should balance it perfectly at the minimum makeup setting. When you have it balanced adjust the interface so both MAC outputs are 1.23va...

Check with VU/OFF/GR in off that you have identical output levels ? Y/N I have both channels of the opto receiving 1.23 VAC and the outputs of the opto are the same but they have dropped to 1.197 VAC. This is hard relay bypass so the level difference is your interface sagging slightly under the loa...

Sorry but I am still confused on the inside / outside part. Before I pull these boards out because I can’t reach the front six soldering points cause they are covered by the case lip. Can I measure from the back 6 solder pads on each pot? Are these part of the switch or the potentiometer? I have ci...

Okay so terribly slow with this over new year but I sourced some pot cleaner and the problem has remained unfortunately! OK as I mentioned up the page. Can you get the pot of the pot PCB ok without damaging it? Otherwise you will need another pot kit. Ok managed to get make-up gain pot off the PCB ...

If the voltages don't match turn off the comp and leave off for a while and measure the outside pins of the threshold and makeup pots still fully CCW. (Like left threshold 95.76k and right threshold 102.54k and left makeup 9.33k and right makeup 11.11k. be as accurate as you meter shows) Which ones...

Does anyone know how I can get the two channels a little bit closer in measurements. It seems that I have to throw a lot more signal at channel B than A by looking at the Volts AC. VAC. Almost .5 DB extra on the fader coming out of my DAW to get 1.23 VAC on the B Channel. Is it the output pots that...

Hi Joe I have built the amp I got from your shop last Monday morning and it is going very well. Thanks for all your help. I believe there is a 'mod' I can do "With no volume control fitted the +/-vol pins can be used to do EQ like low end extension by adding a resistor and capacitor" What resistor ...

super, Joe, thank you! just to make sure I understand correctly, is the below roughly what you mean? And is there a way for me to understand how to calculate the value for R13/R14 correctly? If it's too complicated to explain, let's just say I'll stick with the NE5532A :) Yes that is correct. NE553...

If I'm building this, I'm thinking I might as well take the chance to customise it to my needs, and I'm wondering can I annoy you with a few more questions? I'd like to add a mute switch (with LED lit while muted), an extra Balanced TRS output, and an extra unbalanced TS out for using a tuner (only...

Thanks! That sounds like it should work. I want to run 2 or 3 AMP kits from that 300W PSU. Any suggestions how to implement a soft start or delayed start if that proves necessary? Start with no soft start and see if the SMPS can start the amp without going into hiccup mode. Soft start is easy but y...

oh super stuff, Joe, that is great. thank you! re the opamps, I was thinking of going the DIY route with either a pair of garOA10's or a pair of Pier Paolo's APP992's, if you think they'd work o.k.? I'm planning on ending up with a LOT of your JLM99v's in other equipment in the studio (I've already...