Search found 10 matches
- Wed Oct 29, 2014 11:16 pm
- Forum: JLM Audio Kits
- Topic: Regurgitator kit Build Thread
- Replies: 124
- Views: 436376
Re: Regurgitator kit Build Thread
Thanks, each output (L&R) is buffered by 5534's, and then fed via 22uF and 3K65 to output pins. I think these could be used stand alone as they are now. I basically like'd to do a two four-to-one sums from left and right signals. Perfect. Just connect the 4 x L and run into +in on regurgitator (lin...
- Wed Oct 29, 2014 7:23 am
- Forum: JLM Audio Kits
- Topic: Regurgitator kit Build Thread
- Replies: 124
- Views: 436376
Re: Regurgitator kit Build Thread
Could the regurgitators be used as a summing make-up gain amp? I have four input modules from an old broadcast desk, each have unbal post fader/pan L+R outputs. I'd like to sum those as L+R. With suitable resistors they could be summed and gain lifted? Or something else? Yes can be done easily. Jus...
- Sat Oct 18, 2014 5:34 am
- Forum: JLM Audio Kits
- Topic: Regurgitator kit Build Thread
- Replies: 124
- Views: 436376
Re: Regurgitator kit Build Thread
Could the regurgitators be used as a summing make-up gain amp? I have four input modules from an old broadcast desk, each have unbal post fader/pan L+R outputs. I'd like to sum those as L+R. With suitable resistors they could be summed and gain lifted?
Or something else?
Or something else?
- Tue Nov 20, 2012 7:17 am
- Forum: JLM Audio Kits
- Topic: BAN Build Thread
- Replies: 132
- Views: 504113
Re: BAN Build Thread
Ok, done and works now beatifully.
Thank you Joe.
Thank you Joe.
- Sat Nov 17, 2012 5:12 am
- Forum: JLM Audio Kits
- Topic: BAN Build Thread
- Replies: 132
- Views: 504113
Re: BAN Build Thread
Joe, now I am clueless. The new trimpot did not help, and the old one was faulty. But still I did not get the 16V. Now I removed all the #-parts and put it into normal 48V mode. There should be between 24 to 48 volts on those 470µF caps on the + side, right? Near that #10k resistor I have very close...
- Wed Nov 14, 2012 7:23 am
- Forum: JLM Audio Kits
- Topic: BAN Build Thread
- Replies: 132
- Views: 504113
Re: BAN Build Thread
Thank you.
Now I have two boards, one singing beatifully but with the another I cant get correct voltages. Either I have broken the 10k trimmer or the #681 is faulty.
The voltages are now: 0v - TP1 = 30,8V, 0v - TP3 = 1V, TP3 -TP1 = 29,6V no matter how I turn the trimmer.
What you say?
Now I have two boards, one singing beatifully but with the another I cant get correct voltages. Either I have broken the 10k trimmer or the #681 is faulty.
The voltages are now: 0v - TP1 = 30,8V, 0v - TP3 = 1V, TP3 -TP1 = 29,6V no matter how I turn the trimmer.
What you say?
- Mon Nov 12, 2012 9:06 pm
- Forum: JLM Audio Kits
- Topic: BAN Build Thread
- Replies: 132
- Views: 504113
Re: Correct voltages?
Hello, I am almost done with my new BANs with gar2520. The 10k trim is set to 15V. Is this ok? Just leave the 10k trim pot at the rear of the BAN PCB in it centre position it comes set to new. No adjustment is needed with a 2520. To re-centre pot turn until hear clicking and turn back 12.5 turns. C...
- Mon Nov 12, 2012 7:05 am
- Forum: JLM Audio Kits
- Topic: BAN Build Thread
- Replies: 132
- Views: 504113
Correct voltages?
Hello, I am almost done with my new BANs with gar2520. The 10k trim is set to 15V. Is this ok?
The 2604 is fitted but the 2520 is not and the phantom led is very dim. I'm getting correct 48V on the input but between the phantom legs it is about 20V. Ok?
The 2604 is fitted but the 2520 is not and the phantom led is very dim. I'm getting correct 48V on the input but between the phantom legs it is about 20V. Ok?
- Mon Apr 23, 2012 7:02 pm
- Forum: JLM Audio Kits
- Topic: BA BA2 BA4 BAD Dual99v Build Thread
- Replies: 376
- Views: 1018751
Re: BA BA2 BA4 BAD Dual99v Build Thread
Hi Joe! Almost there, but I want be sure of some details before booting this thing (BA with JML14 + Hybrid + 315mA SMPS). - #10k fitted and extra wire - #BD681 - a small brown cap, reading "281". Where is this supposed to go? On a CLFixed I have "221". - There was not a RG (68 ohm resistor) on the ...
- Fri Apr 20, 2012 3:10 am
- Forum: JLM Audio Kits
- Topic: BA BA2 BA4 BAD Dual99v Build Thread
- Replies: 376
- Views: 1018751
Re: BA BA2 BA4 BAD Dual99v Build Thread
Hi Joe! Almost there, but I want be sure of some details before booting this thing (BA with JML14 + Hybrid + 315mA SMPS). - #10k fitted and extra wire - #BD681 - a small brown cap, reading "281". Where is this supposed to go? On a CLFixed I have "221". - There was not a RG (68 ohm resistor) on the p...