Thanks Joe.
I did test the ACDC briefly, and it worked like you said.
Search found 10 matches
- Sun Dec 09, 2012 4:15 am
- Forum: JLM Audio Kits
- Topic: Acdc voltage issue
- Replies: 6
- Views: 17478
- Wed Dec 05, 2012 8:00 pm
- Forum: JLM Audio Kits
- Topic: Acdc voltage issue
- Replies: 6
- Views: 17478
Re: Acdc voltage issue
1 x 22vac to 25vac between the 0v and one AC in will work fine but the update to the capacitor bank will only we half wave 50 or 60Hz causing high ripple. Using 2 out of phase 22vac windings both between 0v and both AC ins will give same unreg voltage but at full wave rectification of 100 or 120Hz ...
- Wed Dec 05, 2012 4:21 pm
- Forum: JLM Audio Kits
- Topic: Acdc voltage issue
- Replies: 6
- Views: 17478
Re: Acdc voltage issue
Hi there I have a version 2 or 3 ACDC. I want to use it to power a couple ADR scamp modules which require +/- 28vdc. The acdc has been sitting in a drawer for a while. I powered it up today and for some reason i can only adjust the phantom voltage up to about 33vdc and the bipolar rails only up to ...
- Wed Dec 05, 2012 2:58 pm
- Forum: JLM Audio Kits
- Topic: Acdc voltage issue
- Replies: 6
- Views: 17478
Acdc voltage issue
Hi there I have a version 2 or 3 ACDC. I want to use it to power a couple ADR scamp modules which require +/- 28vdc. The acdc has been sitting in a drawer for a while. I powered it up today and for some reason i can only adjust the phantom voltage up to about 33vdc and the bipolar rails only up to a...
- Mon Mar 28, 2011 1:33 am
- Forum: JLM Audio Kits
- Topic: AC/DC & POWERSTATION KIT BUILD THREAD
- Replies: 350
- Views: 862851
Re: AC/DC & POWERSTATION KIT BUILD THREAD
Why not just stuff as per the diagram? It already shows everything you need.
Then you have the 48v there just in case...
Then you have the 48v there just in case...
- Fri Aug 06, 2010 12:12 pm
- Forum: JLM Audio Kits
- Topic: Powerstation supply voltages creeping
- Replies: 2
- Views: 11082
Re: Powerstation supply voltages creeping
Thanks Joe. I have them bolted to the case, so they're pretty cool under load. I'll try adjusting them after they've been on for a bit...
Darrick
Darrick
- Sun Jul 25, 2010 1:22 am
- Forum: JLM Audio Kits
- Topic: Powerstation supply voltages creeping
- Replies: 2
- Views: 11082
Powerstation supply voltages creeping
Hey Joe, I have a powerstation powering eight 1290's. I've noticed that the supply voltages seem to be creeping upwards. I'll set them for 24.05...use the pre's/test them..etc. Shut them off for a day, turn the power supply back on the next day...and the voltages are up around 24.40? I think this th...
- Mon Jul 19, 2010 12:17 pm
- Forum: JLM Audio Kits
- Topic: Go between troubleshooting - phantom
- Replies: 3
- Views: 12783
Re: Go between troubleshooting - phantom
Thanks Joe.
Darrick
Darrick
- Sat Jul 17, 2010 1:31 am
- Forum: JLM Audio Kits
- Topic: Go between troubleshooting - phantom
- Replies: 3
- Views: 12783
Re: Go between troubleshooting - phantom
Hi guys,
Found the problem with the popping. A very fine piece of copper strand on the backside. Removed, tested good.
Still wondering about the 48v at the input transformer primary?
Found the problem with the popping. A very fine piece of copper strand on the backside. Removed, tested good.
Still wondering about the 48v at the input transformer primary?
- Sat Jul 17, 2010 12:58 am
- Forum: JLM Audio Kits
- Topic: Go between troubleshooting - phantom
- Replies: 3
- Views: 12783
Go between troubleshooting - phantom
Hi guys, I have a Go between that's popping when 48v is enabled/disabled; the phase/pad pop when the 48v is activated too. The popping seems to gradually decrease after time at the pad/phase when repeatedly switched. Is this a short? Bad cap? Also, on the channels that do work ok...i have 48v at the...