Search found 86 matches

by kante1603
Sun Feb 04, 2024 3:34 pm
Forum: JLM Audio Kits
Topic: VUPPM500 KIT Build Thread
Replies: 29
Views: 52164

Re: VUPPM500 KIT Build Thread

Hello everybody, have built the kit within some hours yesterday.It was easy to do and complete up to last screw. A nice project for a rainy day.... Adjustment was super-easy.Please mount the trim pots in the right direction indicated by a little slotted screw sign on the pcb.This way levels for trim...
by kante1603
Sat Mar 02, 2019 10:57 pm
Forum: JLM Audio Kits
Topic: VUPPM500 KIT Build Thread
Replies: 29
Views: 52164

Re: VUPPM500 KIT Build Thread

Wonderfull,Joe!
Looking forward to see the AES/SPDIF options.
Is it possible to build it analogue and add digital input-cards(?) later?

Best regards from munich,

Udo.
by kante1603
Mon Nov 12, 2018 8:14 pm
Forum: JLM Audio Kits
Topic: 8 Channel Relay Switch Build Thread
Replies: 37
Views: 88502

Re: 8 Channel Relay Switch Build Thread

Aaaaaahhhhhaaaahhhh! :D That clears it up,thank you Joe. So if we use 24vdc relais we use 24vdc as supply voltsge and put in a 7812 for the ULN 2803,right? I think confusion came from the schematics.Because the dc feed to the relais is written as „V+“ which is after(!) the regulator. I will find out...
by kante1603
Mon Nov 12, 2018 2:46 pm
Forum: JLM Audio Kits
Topic: 8 Channel Relay Switch Build Thread
Replies: 37
Views: 88502

Re: 8 Channel Relay Switch Build Thread

Thank you for the fast reply Joe. But I‘m a bit confused now. When will we use the regulator (and corresponding caps)? I understood how the control port works and would have gone to feed my dc in Version 1 exactly there-because of four linked pads on each side.In version 2 it seems to be two pairs e...
by kante1603
Sun Nov 11, 2018 7:26 pm
Forum: JLM Audio Kits
Topic: 8 Channel Relay Switch Build Thread
Replies: 37
Views: 88502

Re: 8 Channel Relay Switch Build Thread

Hello Joe, I‘ve ordered one of these kits (12vdc version),it is on its‘ way to me now. I see there are two versions now and don‘t know which one I will receive.I‘m happy with either one. Just in case it is V2: 1.:The added regulator is to add more stabilty (I‘m a bit concerned about 78xx type regs,p...
by kante1603
Sun Nov 04, 2018 3:22 pm
Forum: JLM Audio Kits
Topic: Talkback Comp Build Thread
Replies: 23
Views: 63022

Re: Talkback Comp Build Thread

Hi Joe, if I‘m right then first things first: HAPPY BIRTHDAY!!! :D (I‘m in the same „league“) Have built it today,looking good so far. Am I right that the output is quite hot? Can you tell us a rough gain range for Rgain (from ccw to cw) with the compressor disabeled? The compressor bias went well,a...
by kante1603
Sun Nov 04, 2018 3:45 am
Forum: JLM Audio Kits
Topic: Talkback Comp Build Thread
Replies: 23
Views: 63022

Re: Talkback Comp Build Thread

Hi Joe, thank you for the schematics! So D9 (Zener) can be omitted,yes? It‘s also not in the BOM. Shorting it out enables the compressor whether by closing/switching the threshold connector or directly by wire. If we don‘t need the comp. we just leave it open (meaning omit D9)? Can we bring the gain...
by kante1603
Sat Nov 03, 2018 3:54 pm
Forum: JLM Audio Kits
Topic: Talkback Comp Build Thread
Replies: 23
Views: 63022

Re: Talkback Comp Build Thread

Thanks a lot Joe,

looking forward to receive the schematics,will definetely make things clearer for me.

Best regards,

Udo.
by kante1603
Fri Nov 02, 2018 12:11 am
Forum: JLM Audio Kits
Topic: Talkback Comp Build Thread
Replies: 23
Views: 63022

Re: Talkback Comp Build Thread

Thank you very much Joe,

ordered some stuff some minutes ago.
Will you send the schematics (watermarked as always) with the Talkback Compressor kit?

Have a nice day,

best regards,

Udo.
by kante1603
Thu Nov 01, 2018 7:20 pm
Forum: JLM Audio Kits
Topic: Talkback Comp Build Thread
Replies: 23
Views: 63022

Re: Talkback Comp Build Thread

Hello Joe, hope you‘re fine and had a good time at the AES.Seems some beautifull things are coming (I loved the 500 series VUPPM and the FX processor announcements!). For the Talkback Comp: 1.:I‘d like to have full phantom power because I use condenser type microphones which need full +48vdc.Can I d...
by kante1603
Tue Nov 07, 2017 4:00 am
Forum: JLM Audio Kits
Topic: dINgO Pup kit BUILD THREAD
Replies: 79
Views: 262109

Re: dINgO Pup kit BUILD THREAD

HI Udo The dingo 4 mounting holes are not connected to the 0v on the dingo pcb unless you fit the chassis/gnd link next to the input XLR. The 2 pads under the XLR positions are wired to the XLR chassis pins but this goes no where when no XLR's are fitted. If using a floating 48v smps on plastic iso...
by kante1603
Mon Nov 06, 2017 2:31 am
Forum: JLM Audio Kits
Topic: dINgO Pup kit BUILD THREAD
Replies: 79
Views: 262109

Re: dINgO Pup kit BUILD THREAD

Hi Joe, hope you're fine. A quick question: Should the pcbs-when mounted using the pcb holes-better be isolated from chassis? I just wonder because when measuring between the holes' metal rings and 0v on pcb I have the 10 Ohms as expected. Which is the best way,using isolated or metal bolts/screws t...
by kante1603
Tue Oct 31, 2017 10:22 pm
Forum: JLM Audio Kits
Topic: LA500 opto comp leveling amp BUILD THREAD 500/51X
Replies: 223
Views: 570714

Re: LA500 opto comp leveling amp BUILD THREAD 500/51X

G-Sun wrote:Now, look here
Seems like we've found the course.
Remember when soldering that this spot seemed a little weak :)

Fixed. Working perfect again. Thank you!
Looks like an LA500A to me,not LA500.
Wrong thread......?
by kante1603
Sat Oct 21, 2017 2:43 am
Forum: JLM Audio Kits
Topic: LA500 opto comp leveling amp BUILD THREAD 500/51X
Replies: 223
Views: 570714

Re: LA500 opto comp leveling amp BUILD THREAD 500/51X

Hi! My meter-light died. How may I replace it? Hello G-sun, the squared and the round part can be detached.Take care when doing that,gently tear them apart.No brutal force please,or you might damage the meter or bend the needle. Then gently tear apart the white inlay. After that you can reach the l...
by kante1603
Mon Sep 18, 2017 4:37 pm
Forum: JLM Audio Kits
Topic: STATTEN Build Thread
Replies: 12
Views: 34526

Re: STATTEN Build Thread

Thank you Joe, 1.) Looking at the first pic,does that mean the STATTEN pcb takes ALPS RK27xxxxx series pots? I have quite a few of them. 2.) So the "pan pcb" can be directly attached the "volume pcb",yes? 3.) Talking about pan,isn't this balance instead? 4.) When do we use u-pads,when h-pads ( havin...