Search found 12 matches

by Rocinante
Thu Dec 29, 2016 3:54 am
Forum: JLM Audio Kits
Topic: DINGO PCB and kit BUILD THREAD
Replies: 104
Views: 129107

Re: DINGO PCB and kit BUILD THREAD

Okay I am going a little crazy. So I am using two dingos in a monitor controller. I had them up and running I thought, One is working fine right now, the other is.... Not. I am using Ne5532's. I have a signal tracer and the signal stops at R9/R10. I have replaced R9 and R10. I swapped the Ne5532's. ...
by Rocinante
Thu Oct 13, 2016 2:19 am
Forum: JLM Audio Kits
Topic: Passive Controller Build Thread
Replies: 32
Views: 20177

Re: Passive Controller Build Thread

Thanks Joe I would have never figured that out. And so Out B and Ext in are additional in and out?
by Rocinante
Wed Oct 12, 2016 12:20 am
Forum: JLM Audio Kits
Topic: Passive Controller Build Thread
Replies: 32
Views: 20177

Re: Passive Controller Build Thread

Joe Unfortunately I don't have the ribbon cable and am gonna be connecting the ins to the summing bus of my mixer as well as an external in. The outs will be connected to some Regurgitators that I am using for my monitor outs. I have made another little diagram could you please check it for me. I ho...
by Rocinante
Mon Oct 10, 2016 11:58 pm
Forum: JLM Audio Kits
Topic: Passive Controller Build Thread
Replies: 32
Views: 20177

Re: Passive Controller Build Thread

Hey Joe
Is there a link that shows the db25 or jlm io port pin outs? I've searched all over but i can't find a definitive jlm io port schematic anywhere or at the very least a pcb which i can retrace the circuit backwards to figure it out myself.
Thanks
Dylan
by Rocinante
Sat Oct 08, 2016 10:47 am
Forum: JLM Audio Kits
Topic: Passive Controller Build Thread
Replies: 32
Views: 20177

Re: Passive Controller Build Thread

Thank you thank you thank you. You just made my life sooooo much easier.


Cheers
Dylan
by Rocinante
Sat Oct 08, 2016 1:28 am
Forum: JLM Audio Kits
Topic: Passive Controller Build Thread
Replies: 32
Views: 20177

Re: Passive Controller Build Thread

And for clarity purposes I would wire it like below?




Imageimage ru
by Rocinante
Fri Oct 07, 2016 1:13 pm
Forum: JLM Audio Kits
Topic: Passive Controller Build Thread
Replies: 32
Views: 20177

Re: Passive Controller Build Thread

A thousand Thank you's Joe.
by Rocinante
Fri Oct 07, 2016 3:08 am
Forum: JLM Audio Kits
Topic: Passive Controller Build Thread
Replies: 32
Views: 20177

Re: Passive Controller Build Thread

If the centre rotary mode switch mono, stereo , rev is not fitted the mode connector can allow these functions to be done with external switches instead. Care to elaborate (via a diagram if possible :wink: )but I'd definitely suffice with an explanation. I'm leaning in this external switch directio...
by Rocinante
Thu Oct 06, 2016 9:05 am
Forum: JLM Audio Kits
Topic: Passive Controller Build Thread
Replies: 32
Views: 20177

Re: Passive Controller Build Thread

Thanks a bunch Joe for the replies. I had read this article and built their project years ago. To see it on a pcb is awesome especially that you made it so modifiable.
Cheers
by Rocinante
Thu Oct 06, 2016 12:45 am
Forum: JLM Audio Kits
Topic: Passive Controller Build Thread
Replies: 32
Views: 20177

Re: Passive Controller Build Thread

If the contacts link top to bottom then yes should work perfectly. but not sure how you will make the led turn on and off :-) Yes the contacts are supposed to link top to bottom of each side. I believe when the button is engaged it turns the led on but I haven't used them yet. They are also rated a...
by Rocinante
Thu Oct 06, 2016 12:11 am
Forum: JLM Audio Kits
Topic: Passive Controller Build Thread
Replies: 32
Views: 20177

Re: Passive Controller Build Thread

Okay a few more questions.
The farthest left switch is the 'source' or 'input' switch. Is it an A - B switch or is there a mute in between?
What is 'mode" on the bottom right? Another mode switch?
And finally the pot is probably 10k dual gang rev log?
Cheers
And thank you.
by Rocinante
Wed Oct 05, 2016 5:08 pm
Forum: JLM Audio Kits
Topic: Passive Controller Build Thread
Replies: 32
Views: 20177

Re: Passive Controller Build Thread

I've got these great illuminated push button EAO switches I'd like to use for my mute and dim switches. The switches have four pins (not including the led power pins) and are dpst. Can I wire them like I've drawn in the pic below? Thanks again Joe! Dylan https://s26.postimg.org/e8suks2vt/Passive_Con...

Go to advanced search