Full Dual 99v Mic pre kit with everything

1 x 1 unit high rack case with lasered front panel.
2 x OEP A262A3E input transformers.
2 x JLM111DC output transformers.
2 x 3 pin Male XLR.
2 x 3 pin Female XLR.
1 x 5 pin Male XLR.
1 x 5 pin Female XLR inline.
1 x Fuse Holder.
2 x 1Amp Slow Blow Fuse.
10 x self tapper screws.
7 x 3mm flat washers.
3 x 3mm x 10mm bolts.
10 x 3mm x 6mm bolts.
5 x 3mm nuts.
5 x 3mm x lock washers.
2 x 10mm metal standoff.
2m x Shielded cable.
1m x red hook up wire.
1m x black hook up wire.
1m x Green hook up wire.
1m x Yellow hook up wire.
1 x Heatshrink 3mm.
1 x Heatshrink 5mm.
1 x Stick on Foam rubber
4m x Solder.

1 x Front panel kit.
	2 x 5k log pot with pull switch.
	2 x 3mm RED Bezel Chrome.
	1 x 3mm Green Bezel Chrome.
	1 x Large toggle switch (2 nuts, 1 flat washer, 1 lock washer).
	4 x chicken head knobs.
	2 x 100F 50v BP cap.
	2 x 100pF 50v ceramic cap.
	2 x 1mm x 5mm metal tabs.
	1 x 10k

1 x AC/DC power supply kit.
	1 x JLM AC/DC PCB
	2 x LM317 Reg
	1 x LM337 Reg
	1 x 36v 1watt zener
	13 x IN4004
	3 x 5k 25turn trim pots
	8 x 1000uF 50v 105degree Low ESR type
	6 x 10uF 63v 105degree Low ESR type
	1 x 0.1uF 50v Mono
	1 x 10R
	3 x 120R
	2 x 22k
	1 x 3way terminal block
	2 x 2way terminal block
	3 x plastic bush for To220 
	3 x Silicon Rubber insulator for To220
	3 x 3mm bolt 10mm long
	3 x 3mm hex nut
	3 x 3mm lock washer

2 x Dual 99v kits.
	1 x JLM99*MBPCB
	2 x JLM99V
	12 x Gold IC pins for 99v socket mounting
	1 x Dual Rev log 10k pot
	1 x pot NUT for rev log pot
	1 x pot Washer for rev log pot
	2 x 1000uF 10v C23,C24
	3 x 100uF 50v C25,C26,C27
	2 x 100uF 50v BiPolar C9,C19
	2 x 10uF 63v EXR C1,C4
	5 x 0.1uF 50v beads C2,C11,C12,C21,C22
	2 x 47pF ceramic cap C10,C20
	1 x 0R R11
	2 x 10R R28,R29
	2 x 51R R24,R25
	2 x 100R R6,R30
	1 x 300R R18
	3 x 470R R4,R5,R7
	2 x 1k R15,R22 (use if you want 70dB max gain with JLM1:4 or LL1538 set to 1:2.5ratio)
	2 x 1k5 R15,R22 (use if you want 70dB max gain with A262A3E or LL1538 set to 1:5 ratio ot LL1578)
	2 x 1k8 R15,R22 (use if you want 60dB max gain all input trasnformers)
	1 x 5k6 R10 if using LL1538 input transformer(if you want brighter LL1538 sound use 47k) 
	2 x 6k8 R1,R2
	1 x 10k R10 if using JLM1:4 input transformer
	2 x 22k R16,R23
	1 x 27k R10 if using A262A3E input transformer
	1 x 47k R10 if using LL1578 input transformer
	2 x 100k R26,R27
	6 x 3way terminal block
	2 x 2way terminal block
	1 x 2x2 jumper pins
	1 x 1x3 jumper pins
	3 x computer jumpers
	8 x 3mm bolt 6mm long
	8 x 3mm lock washer
	4 x 10mm metal threaded PCB stand off

	1 x JLMSWPCB
	1 x LM317 Reg1
	3 x 0.1uF 50v Beads C28,C29,C30 (C30 is marked as a second C28 on the PCB)
	1 x 33R R8
	3 x 300R R31,R32,R33
	3 x 5v DPDT relays
	3 x toggles
	6 x nuts for toggles
	3 x flat washers for toggles
	3 x lock washers for toggles 
	3 x 3mm Red LED LED1,LED2,LED3
	2 x 2way terminal block

2 x DI kits.
	1 x JLM DI PCB
	1 x TRS socket PCB mount with DPDT switch
	1 x Nut for TRS socket
	1 x 8 pin machined IC socket
	1 x OPA2604 Burr Brown opamp
	2 x 100uF 50v Bi Polar Caps
	1 x 100uF 63v 105 degree electro cap
	3 x0.1uF 50v caps
	2 x 51R
	2 x 300R
	2 x 100k
	4 x 2.2Meg
	1 x 10pin IDC Socket
	2 x 3way terminal blocks
	2 x 10way IDC plugs and 
	1 x 10way flat cable in parts